Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

After installation, the car must not be washed for 48 hours

When installing, the car must retain a temperature of 20 degrees C.

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Paintwork

Clean the surface.

Use: 1161721, Isopropanol

Matt the surface gently.

Use: , Sand paper P1000

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

Use: , Volvo Original Touch-up paint

Use base coat only.

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

Removal

Set the ignition key to position 0.

Measure and mark as illustrated.

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Accessory installation

Removal

Remove the screws.

Repeat on the other side.

Remove the screws.

Repeat on the other side.

Disconnect the connector, if applicable.

Vehicles with keyless entry

Disconnect the connector.

The cable harness must not be reused.

Vehicles with integrated Exhaust End Pipes

Remove the clip.

Repeat on the other side.

The part is not to be reused.

Applies to all other vehicles

The part is not to be reused.

Accessory installation

Vehicles with integrated Exhaust End Pipes

Install component that comes with the accessory kit.

Install the clip(s).

Repeat on the other side.

Applies to all other vehicles

Install component that comes with the accessory kit.

All vehicles

Locate the markings for the positions.

Mark the centre.

Use special tool: T9997234, Hole stamp

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

Removal

Vehicles with keyless entry

Accessory installation

All vehicles

Locate the existing connector in the vehicle's cable harness.

Connect the connector.

Connect the prerouted cable.

Remove the protective film.

Remove the protective film.

Note position of components.

Remove the protective film.

Install component that comes with the accessory kit.

Remove the protective film.

Install component that comes with the accessory kit.

Put the wiring in the Bumper cover without installing the wiring.

Connect the two painted sensors to the external connections.

Fasten the wiring harness using the existing clips.

Vehicles with keyless entry

Connect the connector.

Vehicles without keyless entry

All vehicles

Place the Bumper Cover in position for installation.

Connect the connector.

Reinstall the removed parts in reverse order.

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31266966