| | Note!
Some steps in these installation instructions are presented with illustration only. |
|
| | IMG-352652 |
|
| | |
| | IMG-352653 |
|
| | |
| | IMG-352654 |
|
| | |
| | IMG-352653 |
|
| | |
| | IMG-352655 |
|
| | Caution!
Protect the connections' contact surfaces against paint. |
Paint the sensors in the same colour code as the vehicle. Use Volvo Touch-up paint (only use base coat). Use: Volvo 2-K Varnish, P/N: 31335447
Note!
Also read the instructions on the spray can. |
|
| | IMG-352658 |
|
| | Caution!
The paint must have dried after the first application. |
|
| | IMG-332193 |
|
| | Note!
Wait at least one minute before unplugging the connectors or removing other electrical equipment. |
|
| | IMG-354292 |
|
| | |
| | IMG-354291 |
|
| | |
| | IMG-349806 |
|
| | |
| | IMG-345282 |
|
| | |
| | IMG-339505 |
|
| | Applies to vehicles with manual transmissions |
| | IMG-347222 |
|
| | |
| | IMG-293006 |
|
| | Applies to vehicles with automatic transmissions |
| | IMG-293007 |
|
| | |
| | IMG-292804 |
|
| | |
| | IMG-340599 |
|
| | Fold back the mat. Unhook the cable harness clips. Unplug the connector.
|
| | IMG-353601 |
|
| | |
| | IMG-353602 |
|
| | Remove the covers. Remove the screws.
|
| | IMG-292826 |
|
| | Applies to vehicles with the 4-C system |
| | IMG-345317 |
|
| | |
| | IMG-349826 |
|
| | Applies to all models Caution!
Do not damage the hooks. |
|
| | IMG-345295 |
|
| | |
| | IMG-345296 |
|
| | |
| | IMG-340638 |
|
| | |
| | IMG-353570 |
|
| | |
| | IMG-247266 |
|
| | |
| | IMG-211568 |
|
| | |
| | IMG-247267 |
|
| | Pull the corner straight out, continue to pull the bumper cover backwards until the five clips at the upper edge release. Repeat the operation on the other side.
|
| | IMG-247268 |
|
| | |
| | IMG-352668 |
|
| | |
| | IMG-352669 |
|
| | |
| | IMG-352670 |
|
| | |
| | IMG-352671 |
|
| | Use special tool: 9997234 Hole tool Caution!
The cutting part of the tool must be on the outside of the cover. |
|
| | IMG-352672 |
|
| | |
| | IMG-352667 |
|
| | |
| | IMG-352673 |
|
| | |
| | IMG-352666 |
|
| | |
| | IMG-226907 |
|
| | |
| | IMG-226722 |
|
| | |
| | IMG-255684 |
|
| | |
| | IMG-255685 |
|
| | Remove: Unplug connector for 12V outlet, if installed. |
| | IMG-247272 |
|
| | |
| | IMG-247273 |
|
| | |
| | IMG-247274 |
|
| | |
| | IMG-247275 |
|
| | |
| | IMG-247276 |
|
| | |
| | IMG-247277 |
|
| | |
| | IMG-247278 |
|
| | |
| | IMG-247279 |
|
| | |
| | Reinstall: the side panels the sill trim panel the floor carpet Fold up the backrest.
|
| | |
| | IMG-247283 |
|
| | |
| | IMG-247284 |
|
| | |
| | IMG-352674 |
|
| | Note!
The adhesive must be above the level for the tape. |
Caution!
The adhesive must not come into contact with the tape. |
Use special tool: 9512950 Adhesive gun. Use: 1161730 Mixing pipe. Use: 9511027 Adhesive. |
| | IMG-247286 |
|
| | Install the centering tool in one holder. Install the holder on the bumper cover. Hold the holder securely when removing the centering tool. The holder must be installed horizontally and in line with the bumper cover. Repeat the steps until all four holders are in place.
|
| | IMG-247287 |
|
| | |
| | IMG-247288 |
|
| | Note!
The large gray connector must protrude from the right-hand side of the bumper cover. |
|
| | IMG-247289 |
|
| | |
| | |
| | IMG-247290 |
|
| | Installing the bumper Lift up the bumper and connect the connector Press all of the bumper's hooks in at the rear edge. Press all the hooks for the ends into the body. Reinstall the screws on the front edges of the bumper casing. Reinstall the plastic nuts at the lower edge.
|
| | IMG-242268 |
|
| | |