| | |
| | IMG-352652 |
|
| | Preparations Applies to the V70 |
| | IMG-352653 |
|
| | |
| | IMG-352654 |
|
| | |
| | IMG-352653 |
|
| | |
| | IMG-352655 |
|
| | Caution!
Protect the connections' contact surfaces against paint. |
Paint the sensors in the same colour code as the vehicle. Use Volvo Touch-up paint. (Only use base coat.) Use: Volvo 2-K Varnish. P/N: 31335447
Note!
Also read the instructions on the spray can. |
|
| | IMG-352658 |
|
| | Caution!
The paint must have dried after the first application. |
|
| | IMG-352675 |
|
| | |
| | IMG-344142 |
|
| | |
| | IMG-344141 |
|
| | |
| | IMG-344142 |
|
| | |
| | IMG-344251 |
|
| | Caution!
Protect the connections' contact surfaces against paint. |
Paint the sensors in colour code 426. Use Volvo Touch-up paint. (Only use base coat.) Use: Volvo 2-K Varnish. P/N: 31335447
Note!
Also read the instructions on the spray can. |
|
| | IMG-333934 |
|
| | Caution!
The paint must have dried after the first application. |
|
| | |
| | IMG-245980 |
|
| | Applies to all models Note!
Wait at least three minutes before unplugging the connectors or removing other electrical equipment. |
|
| | IMG-259683 |
|
| | |
| | IMG-259684 |
|
| | |
| | IMG-259685 |
|
| | |
| | IMG-273303 |
|
| | |
| | IMG-273304 |
|
| | Carefully pull off the ends of the bumper cover on both sides. They are secured by hooks at the top edge of the ends and at the lower edge of the rear lights. Pull off the bumper cover from the rear of the body, it is positioned in seven guides at the top edge of the long side.
Note!
It is recommended that two people carry out this step to prevent damaging the bumper cover. |
Place the bumper cover on a suitable surface.
|
| | IMG-259754 |
|
| | |
| | IMG-259756 |
|
| | Carefully pull off the ends of the bumper cover on both sides. They are secured by hooks at the top edge of the ends and at the lower edge of the rear lights. Pull off the bumper cover from the rear of the body, it is positioned in seven guides at the top edge of the long side.
Note!
It is recommended that two people carry out this step to prevent damaging the bumper cover. |
Place the bumper cover on a suitable surface.
|
| | |
| | IMG-283023 |
|
| | |
| | IMG-283024 |
|
| | |
| | IMG-273309 |
|
| | |
| | IMG-283025 |
|
| | |
| | IMG-283026 |
|
| | |
| | IMG-283027 |
|
| | |
| | IMG-283028 |
|
| | |
| | IMG-283030 |
|
| | |
| | IMG-283031 |
|
| | |
| | IMG-273313 |
|
| | |
| | IMG-283032 |
|
| | |
| | IMG-283026 |
|
| | |
| | IMG-283033 |
|
| | |
| | IMG-283028 |
|
| | |
| | IMG-261414 |
|
| | |
| | IMG-273316 |
|
| | |
| | |
| | IMG-273317 |
|
| | |
| | IMG-273318 |
|
| | |
| | IMG-273319 |
|
| | |
| | IMG-273320 |
|
| | |
| | IMG-273321 |
|
| | |
| | IMG-273322 |
|
| | |
| | IMG-273323 |
|
| | |
| | IMG-273324 |
|
| | |
| | IMG-247283 |
|
| | |
| | IMG-247284 |
|
| | |
| | IMG-283034 |
|
| | Apply a thin and even layer of adhesive to a holder. The adhesive must be above the tape level.
Note!
The adhesive must not come into contact with the tape. |
The task of the tape is to secure the holders to the bumper casing until the adhesive has hardened after approximately 24 hours.
|
| | IMG-247286 |
|
| | Install the centering tool in the holder. Install the tool on the bumper cover. Press the holder towards the casing, but only at the places where there is tape. Hold the holder securely when removing the centering tool. The holder must be installed horizontally and in line with the bumper cover. Repeat steps 37-39 until all four holders are in place.
|
| | IMG-247287 |
|
| | |
| | IMG-247288 |
|
| | |
| | IMG-273326 |
|
| | |
| | IMG-273328 |
|
| | |
| | |
| | IMG-273330 |
|
| | Supplementary work Applies to all models |
| | IMG-273331 |
|
| | Press the bumper's hooks in at the rear edge. Press all the hooks for the ends into the body. Reinstall the screws on the front edges of the bumper casing. Reinstall the plastic nuts at the lower edge.
|
| | IMG-273332 |
|
| | |
| | IMG-236046 |
|
| | |
| | IMG-236047 |
|
| | |
| | IMG-242268 |
|
| | |