Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S80 2012
S80 (07-) 2012

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
312017361.231201599, 31269374
Parking assistance, rear




 
Equipment
IMG-242205
IMG-345497
IMG-330288
IMG-330289
IMG-333288
IMG-333293
IMG-332314

IMG-255683


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

  

Note!

During installation, the car and components must maintain a temperature of at least +20° C (68° F).


 

Preparations

1
IMG-352652
 

Preparations

2
IMG-352653
 

  • Clean the sensors. Use: Isopropanol.

  • Allow to dry.

3
IMG-352654
 

  • Carefully mat down the surface. Use Glasspaper, grade P1000.

4
IMG-352653
 

  • Clean the sensors again. Use: Isopropanol

  • Allow to dry

  • Avoid contact with the cleaned surfaces.

5
IMG-352655
 


Caution!

protect the connections' contact surface against paint.


  • Paint the sensors in the same colour code as the vehicle.

  • Use Volvo Touch-up paint. (Only use base coat.)

  • Use: Volvo 2-K Varnish. P/N: 31335447


Note!

Also read the instructions on the spray can.


6
IMG-352658
 


Caution!

The paint must have dried after the first application.


 
7
IMG-247309
 

  • Turn the ignition switch to position 0.


    Note!

    Wait at least one minute before unplugging the connectors or removing other electrical equipment.


8
IMG-247266
 

  • Remove the four screws holding the end of the rear bumper.

    Repeat the operation on the other side.

9
IMG-211568
 

  • Remove the two nuts at the lower edge of the bumper cover.

10
IMG-247267
 

  • Pull the corner straight out, continue to pull the bumper cover backwards until the five clips at the upper edge release.

    Repeat the operation on the other side.

11
IMG-247268
 

  • Open the boot lid/tailgate.

  • Remove the bumper cover by pulling it backwards until the three catches opposite the tailgate opening have released.

 
12
IMG-352668
 

  • Locate the 4 markings on the inside of the bumper cover.

13
IMG-352669
 

  • Mark center with a scribe.

14
IMG-352670
 

  • Drill out the markings using a Ø 3 mm (1/8") diameter drill bit.

  • Drill out the holes. Use a Ø10 mm (13/32") diameter drill bit.

15
IMG-352671
 

  • Use special tool: 9997234 Hole tool.


Caution!

The cutting part of the tool must be on the outside of the cover.


16
IMG-352672
 

  • Clean around the holes and the markings. Use: Isopropanol.

17
IMG-352667
 

  • Take four holders from the kit.

  • Clean the cradles on the surface as illustrated. Use: Isopropanol.

  • Allow to dry.

18
IMG-352673
 

  • Apply a thin and even layer of activator to the cleaned surfaces where the tape is to be attached. Use: 8637076 Activator.

  • Allow to dry for at least 10 minutes.

19
IMG-352666
 

  • Apply a thin and even layer of activator to the cleaned surfaces where the tape is to be attached. Use: 8637076 Activator

  • Allow to dry for at least 10 minutes.

 
20
IMG-226907
 

  • Lift out the cargo compartment carpet.

21
IMG-226722
 

  • Remove the sill trim panel by first pulling it forward until the clips in the front edge release. Then pull it upward until the clips in the top edge release.

22
IMG-255684
 

  • Fold forward the right backrest in the backseat.

23
IMG-255685
 

    Remove:

  • the clips

  • the plastic nuts

  • the connector to the cargo compartment lighting

  • the side panel.

Unplug connector for 12V outlet, if installed.

 

Installation of the Parking Assistance Module (PAM)

24
IMG-247272
 

Installation of the Parking Assistance Module (PAM)

  • Locate the two studs positioned on the right-hand side underneath the tail lamp in the cargo compartment. Press the control module's holder on the studs.

25
IMG-247273
 

  • Press the control module on the holder.

26
IMG-247274
 

  • Remove the rubber seal.

27
IMG-247275
 

  • Remove the support under the left-hand tail lamp by removing the two screws.

28
IMG-247276
 

  • Take the short cable harness and thread the end with the black connector through the hole in the body.

  • Install the rubber grommet.

29
IMG-247277
 

  • Reinstall the support under the left-hand tail lamp.

  • Hook the connector onto the rail.

30
IMG-247278
 

  • Connect the newly routed cable harness to the control module.

31
IMG-247279
 

  • Locate the light brown connector. It originates from the same cable harness as the connector for cargo compartment lighting.

  • Connect the connector to the control module.

32
 

    Reinstall:

  • the side panels.

  • the sill trim panel.

  • the floor carpet.

  • Fold up the backrest.

 

Installing sensors

33
IMG-247283
 

Installing sensors

  • Check which holder is to be positioned where before installing. The two middle holders are the same whilst the two outer holders are specific.

34
IMG-247284
 

  • Apply two pieces of tape to each holder.

  • Remove the protective film from the tape.

35
IMG-352674
 

  • Apply a thin layer and even layer of adhesive.


    Note!

    The adhesive must be above the level for the tape.



    Caution!

    The adhesive must not come into contact with the tape.


  • Use special tool: 9512950 Adhesive gun

  • Use: 1161730 Mixing pipe

  • Use: 9511027 Adhesive.

36
IMG-247286
 

  • Install the centering tool in one holder.

  • Install the tool on the bumper cover.

  • Hold the holder securely when removing the centering tool. The holder must be installed horizontally and in line with the bumper cover.

  • Repeat the steps until all four holders are in place.

37
IMG-247287
 

  • Connect the cable harness connectors to the sensors.

38
IMG-247288
 

  • Install the sensors in their holders. Take care not to release the holders from the tape when installing.


    Note!

    The large gray connector must protrude from the right-hand side of the bumper cover (see image 31).


39
IMG-247289
 

  • Press the six cable holders on the longitudinal flange of the bumper casing.

40
IMG-247290
 

Installing the bumper

  • Lift up the bumper and connect the connector.

  • Press the bumper's hooks in at the rear edge. Press all the hooks for the ends into the body.

  • Reinstall the screws on the front edges of the bumper casing.

  • Reinstall the plastic nuts at the lower edge.

 

Installing the switch

41
IMG-236045
 

Installing the switch

  • Press the panel in at the front edge.

  • Lift the panel at the rear edge and remove it.

42
IMG-236046
 

  • Remove the cover.

43
IMG-236047
 

  • Install the new switch. It must be fitted in the first available button location seen from the steering wheel.


    Note!

    Cover plugs are purchased separately.


  • Reinstall the gear selector panel.

 
44
IMG-242268
 

  • Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.