Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S80 2014
S80 (07-) 2014

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313306041.731414189, 31201481
Tire pressure monitoring system (TPMS)




 

Special tools

 

T9513035 TPMS tool

Tool number: T9513035

Tool description: TPMS tool

Tool boards:


Equipment
A0000162
A0000161
A0801178

IMG-229180


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

  

Note!

This accessory requires software unique to the car.



Note!

Perform installation on all four wheels.



Note!

When installing tyre pressure sensor on complete wheel, the tyre must first be removed from the rim and then fitted as below.


 

Installing tyre pressure sensor on loose rim and tyre

1A
IMG-216861
1B
IMG-216862
 

Installing tyre pressure sensor on loose rim and tyre

Illustration A

Illustration B

  • Clean the inside and outside of the rim by the hole for the tyre valve. Also clean the inside of the hole edge.

2
IMG-238180
 

  • Install the valve in the valve hole without changing the angle between the valve and sensor body. (Keep the setting that the unit was supplied with).

    The laser marking must be visible to the installer.

3
IMG-238181
 

  • When the valve is fully inserted in the valve hole, ensure that the sensor body is against the rim, and then start to manually screw the valve's mounting nut a few turns with the other hand.

4
IMG-238182
 

  • At the same time as keeping the sensor body against the rim by pressing the rear of the valve with one hand, press the valve's mounting nut carefully towards the centre of the rim with the other hand. This is to obtain the correct angle between valve and sensor body whilst the sensor body is against the rim.


    Note!

    It is important that the sensor body maintains contact with the rim.


5
IMG-238183
 

  • Whilst holding the sensor body and valve in position with one hand, tighten the valve's mounting nut with the other. Ensure that the socket fits properly on the mounting nut. Torque tighten the mounting nut to 8 Nm (6 lbf.ft.).

6
IMG-229209
 


Caution!

When fitting the tyre on the rim:

Ensure that the sensor is properly attached to the rim before fitting the tyre.

Lubricate the tyre edges with tyre paste to facilitate fitting.

No tyre paste or other foreign particles may cover the hole (1) for filling with air, or the hole (2) for measuring the air pressure on the sensor.

No pressure may be exerted on the sensor when fitting the tyre.

Ensure that the tyre does not get stuck between rim and sensor when fitting.

Do not use installation tools between the sensor and the edge of the tyre.

The tyre must be fitted so that the tyre pressure sensor moves away from the tyre fitting tool.


7
IMG-238184
 

Fitting tyre onto rim

  • Place the tyre in the tyre machine and lubricate the tyre edges with tyre paste.

8
IMG-238185
 

  • Fit the tyre onto the rim so that the distance between the valve and where the tyre touches the rim is about 200 mm.

9
IMG-238186
 

  • Install the tyre shoe and ensure that the distance of 200 mm between the valve and the touching point between tyre and rim is maintained. The curved arrow shows the rotation of the wheel.

10
IMG-238187
 

  • Turn the wheel to get the tyre's first side into position. The standard shoe can pass over the sensor without damaging it.

11
IMG-238188
 

  • Position the other side of the tyre so that the distance between the valve and where the tyre touches the rim is about 200 mm. The curved arrow shows the rotation of the wheel.

12
IMG-238189
 

  • Turn the wheel to get the tyre's other side into position. The standard shoe can pass over the sensor without damaging it.

13
 

  • Fill the tyre with air and balance it after fitting.

14
A0801178
 

    After fitting the wheels on the car

  • Torque tighten the wheel nuts to 140 Nm (103 lbf.ft).

  • Program the software according to service information in VIDA.

15
IMG-382866
 

  • Calibrate the TPMS sensors.


Use special tool: T9513035, TPMS tool