Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Conditions

There may be parts in the accessories kit that are not needed for this installation.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

7. Used for accessory components.

Paintwork

Preparation

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

Use: , Masking tape

Use: , Masking tape

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

Use: 31335448, Bonding primer, plastic

Also see the instructions on the container.

Allow to dry.

Use: 31335448, Bonding primer, plastic

Also see the instructions on the container.

Allow to dry.

Use: , Volvo Original Touch-up paint

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

Allow to dry.

Use: , Volvo Original Touch-up paint

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

Allow to dry.

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

Matt the surface gently.

Use: , Sand paper P1000

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

Also see the instructions on the container.

Use: , Volvo Original Touch-up paint

Use: 31335447, Varnish 2-component

Allow to dry.

Remove the tape.

Remove the tape.

Remove the panel.

Remove the panel.

Remove the panel.

Use hands only.

Remove the panel.

Use hands only.

Remove the marked part.

The part is to be reused.

Remove the screw.

The part is to be reused.

Tightening torque: Accelerator pedal, to Floor , 6.5 Nm

Remove the marked part.

Remove the marked part.

Remove the screws.

Remove the panel.

Disconnect the connector, if applicable.

Vehicles with driver's knee airbag

Remove the screws.

Remove the screws.

Fold marked part aside.

Tightening torque: Airbag to bracket , 5.5 Nm

Release the connector catches.

Remove the marked part.

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Disconnect the connector.

Unhook the cable harness clips.

Remove the marked part.

Repeat on the other side.

Remove the marked part.

Remove the marked part.

Fold marked part aside.

Remove the screw.

Tightening torque: Seat belt guide, to Bracket , 4.4 Nm

Fold marked part aside.

Use hands only.

Release the catch.

Remove the marked part.

Remove the panel.

Use hands only.

Remove the panel.

Use hands only.

Disconnect the connector, if applicable.

Remove the marked part.

Detach the panel.

Remove the panel.

Remove the marked part.

Remove the marked part.

Fold marked part aside.

Disconnect the connector.

Remove the marked part.

Remove the marked part.

Use: Electrician's screwdriver

Remove the screw.

Tightening torque: M8 , 24 Nm

Remove the marked part.

Remove the marked part.

Use hands only.

Remove the clips.

Remove the cable harness clips.

Fold marked part aside.

Fold the insulation aside.

Remove the clips.

Raise the car.

Remove the screws.

Remove the screws.

Fold the wing liner aside.

Remove the screw.

Loosen the component indicated. Do not remove it.

Use hands only.

Loosen the component indicated. Do not remove it.

Repeat the steps when removing on opposite side.

Disconnect the connector.

Remove the part carefully

Remove the marked part.

Remove the cable harness.

The cable harness must not be reused.

Accessory installation

Locate the markings for the positions.

Mark the centre.

Use: Scribe

Use special tool: T9997685, Hole punch

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

Apply a thin and even layer.

Use special tool: T9512950, Glue gun (kit)

Use: 1161730, Mixing pipe
Use: 9511027, Glue

Install the marked component.

Use tape

Allow to dry.

Also see the instructions on the container.

Remove the tape.

Repeat the steps when installing on opposite side.

Clean the surface.

Use: 1161721, Isopropanol

Use detail according to image.

Apply a thin and even layer.

Use special tool: T9512950, Glue gun (kit)

Use: 1161730, Mixing pipe

Use: 9511027, Glue

Install the marked component.

Use tape

Allow to dry.

Also see the instructions on the container.

Remove the tape.

Use details according to image.

Connect the two painted sensors to the external connections.

Repeated on the right-hand side.

Use detail according to image.

Fasten the wiring harness using the existing clips.

Connect the connectors.

Use detail according to image.

Adjust the position of the wiring harness.

Place the cable tie as illustrated.

Position/route the cable harness as illustrated.

Route the cable harness to the existing cable harness.

Use a cable tie

Place the Bumper Cover in position for installation.

Position/route the cable harness as illustrated.

Connect the connector.

Connect the connector.

Remove the screws.

Fold marked part aside.

Remove the marked part.

The part is not to be reused.

Pull the wiring through.

Reinstall the removed part.

Tighten the bolts.

Tightening torque: Bracket for rear fender , 3 Nm

Reinstall the bumper.

Position/route the cable as illustrated.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Fold the carpet aside.

Clean the surfaces.

Use: 1161721, Isopropanol

Position wire as illustrated.

Install components that come with the accessory kit.

Use: Electrician's screwdriver

Route the wire adjacent to existing wirings.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Removal

Open the hood.

Remove the screws.

Remove the marked part.

Remove the screws.

Remove the marked detail/details.

Repeat on the other side.

Use: Pliers

Remove the screws.

Remove the marked part.

Repeat on the other side.

Tightening torque: Aluminum wheel rim to wheel hub
Stage 1: 4 Nm
Stage 2: 50 Nm
Stage 3: 140 Nm

Remove the screws.

Remove the clips.

Repeat on the other side.

Remove the nut.

Repeat on the other side.

Fold the wing liner aside.

Disconnect the connectors.

Vehicles with headlamp washers

Undo the hose from the connection.

Applies to the right-hand side

Remove the screws.

Remove the clip.

Remove the screw.

Remove the nut.

Remove the marked part.

Remove the screws.

Repeat on the other side.

Tightening torque: Bracket to front fender , 6 Nm

All vehicles

Remove the screws.

Remove the clips.

Remove the marked part.

Remove the clips.

1. Release the catches.

2. Remove the part carefully

3. Remove the marked part.

Remove the cable harness.

The cable harness must not be reused.

Accessory installation

Use special tool: T9997686, Hole punch

Use detail according to image.

1. Hold it down.

2. Screw the tool to mark the center.

Hold it down.

Repeat the steps when installing accessories on opposite side.

Use details according to image.

Connect the two painted sensors to the external connections.

Repeated on the right-hand side.

Use detail according to image.

Fasten the wiring harness using the existing clips.

Connect the connectors.

Reinstall the bumper.

Use detail according to image.

Connect the connector.

Connect the connector.

Adjust the position of the component according to image.

Clamp the cables and connectors to the existing cables to prevent noise.

Position/route the cable as illustrated.

Use a cable tie

Fold marked part aside.

Position/route the cable as illustrated.

Use a cable tie

Use detail according to image.

Position/route the cable as illustrated.

Use a cable tie

Position/route the cable as illustrated.

Use a cable tie

Position/route the cable as illustrated.

Use detail according to image.

Install the cable.

Position/route the cable as illustrated.

Use a cable tie

Position/route the cable as illustrated.

Use a cable tie

Position/route the cable as illustrated.

Use a cable tie

Position/route the cable as illustrated.

Use a cable tie

Position/route the cable as illustrated.

Use a cable tie

Position/route the cable as illustrated.

Use a cable tie

Loosen the hose clamp.

Fold marked part aside.

Release the lock.

Remove the marked part.

Remove the nut.

Fold the insulation aside.

Make a cut in the insulation.

Press the marked component.

The part is not to be reused.

Remove the screws.

Remove the marked part.

Remove the panel.

Fold the carpet aside.

Make a cut in the insulation.

Use detail according to image.

Pull the wiring through.

Use: 1161150, Lubricant

Use special tool: T9814203, Expander pliers

Insert the cable in to the passenger compartment, adjust the cable length out into the engine compartment and secure the rubber grommet.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Removal

Remove the screws.

Remove the marked part.

1. Depress the locking device.

2. Release the connector's catch.

3. Disconnect the connector.

Release the catches.

Remove the marked part.

Release the catches.

Remove the marked part.

Use: Electrician's screwdriver

Use special tool: T9512632, Terminal removal tool (Color code: RED)

Disconnect terminals from the connector, following the graphic.

BN = Brown

GN = Green

GY = Grey

OG = Orange

WH = White

YE = Yellow

VT = Violet

Accessory installation

Connect the prerouted wiring harness.

Connect the cable harness terminals in the connector as follows.

BN = Brown

GN = Green

GY = Grey

OG = Orange

WH = White

YE = Yellow

BU = Blue

VT = Violet

Depress the secondary lock.

Reinstall the removed part.

Removal

1. Depress the locking device.

2. Release the connector's catch.

3. Disconnect the connector.

Release the catches.

Remove the marked part.

Release the catches.

Remove the marked part.

Use special tool: T9512632, Terminal removal tool (Color code: RED)

Disconnect terminals from the connector, following the graphic.

BN = Brown

GN = Green

GY = Grey

OG = Orange

WH = White

YE = Yellow

Accessory installation

Connect the prerouted wiring harness.

Connect the cable harness terminals in the connector as follows.

BN = Brown

GN = Green

GY = Grey

OG = Orange

WH = White

YE = Yellow

Depress the secondary lock.

Reinstall the removed part.

Connect the connectors.

Install the cables.

Use a cable tie

Reinstall the removed part.

Reinstall the screws.

Check that the tire dimension stated in the vehicle configuration, corresponds to the actual tire dimension of the vehicle.

If this does not correspond, download correct software.

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.

Installation

Reinstall the removed parts in reverse order.