| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | |
| | IMG-420103 |
|
| | Clean the surface. Use: , Isopropanol
Allow to dry. |
| | IMG-420104 |
|
| | |
| | IMG-420131 |
|
| | Clean the surface. Use: , Isopropanol
Allow to dry. |
| | IMG-420130 |
|
| | Use: 31335448, Bonding primer, plastic
Also see the instructions on the container. |
| | IMG-384372 |
|
| | |
| | IMG-384853 |
|
| | |
| | IMG-404275 |
|
| | Clean the surface. Use: , Isopropanol
Allow to dry. |
| | IMG-404276 |
|
| | Matt the surface gently. Use: , Sand paper P1000
|
| | IMG-404275 |
|
| | Clean the surface. Use: , Isopropanol
Allow to dry. |
| | IMG-404278 |
|
| | Caution! Protect connector surfaces against paint spray. |
Note! Paint the sensors the same colour code as the vehicle. |
Also see the instructions on the container. Use: , Volvo Original Touch-up paint
Use: 31335447, Varnish 2-component
|
| | IMG-420130 |
|
| | Note! Use correct color following the vehicle's paint code. |
Use: , Volvo Original Touch-up paint
Use: 31335447, Varnish 2-component
Also see the instructions on the container. |
| | IMG-420085 |
|
| | Caution! First the paint must dry after painting. |
|
| | IMG-420132 |
|
| | |
| | |
| | IMG-394535 |
|
| | |
| | Note! The removal steps may contain installation details. |
|
| | IMG-414590 |
|
| | |
| | IMG-412242 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-414575 |
|
| | |
| | IMG-414580 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-414585 |
|
| | Remove the screws. Remove the panel. |
| | IMG-400000 |
|
| | Repeat the steps when removing on opposite side. |
| | IMG-419056 |
|
| | |
| | IMG-414613 |
|
| | |
| | IMG-419060 |
|
| | |
| | IMG-419061 |
|
| | |
| | IMG-419062 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-419063 |
|
| | Remove the panel. Use hands only. |
| | IMG-419065 |
|
| | Release the catch. Remove the marked part. |
| | IMG-417503 |
|
| | Remove the panel. Use hands only. |
| | IMG-419067 |
|
| | Remove the screw. Tightening torque: M6
, 10 Nm
|
| | IMG-417441 |
|
| | Release the lock. Repeat on the other side. Remove the marked part. |
| | IMG-417504 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-422035 |
|
| | Caution! Make sure that the seat backrest upholstery (fold down position) is not damaged by contact with the floor! |
|
| | IMG-422102 |
|
| | |
| | IMG-417505 |
|
| | |
| | IMG-401577 |
|
| | |
| | IMG-401579 |
|
| | |
| | IMG-401580 |
|
| | |
| | IMG-407110 |
|
| | |
| | IMG-414611 |
|
| | |
| | IMG-415830 |
|
| | Repeat on the other side. |
| | IMG-415831 |
|
| | Remove the screw. Tightening torque: M6
, 10 Nm
Repeat on the other side. |
| | IMG-416086 |
|
| | |
| | IMG-416087 |
|
| | |
| | Vehicles with keyless entry |
| | IMG-413321 |
|
| | Disconnect any connector(s). |
| | |
| | IMG-415835 |
|
| | |
| | IMG-416089 |
|
| | |
| | IMG-419165 |
|
| | Remove the panel. Disconnect any connector(s). |
| | IMG-421391 |
|
| | Disconnect the connector. Remove the cable harness clips. |
| | IMG-421395 |
|
| | Remove the clips. Remove the marked part. |
| | IMG-413540 |
|
| | Remove the marked part. Repeat on the other side. Make sure that the components are not mixed up at the installation. |
| | IMG-410325 |
|
| | |
| | IMG-410326 |
|
| | Fold the wing liner aside. |
| | IMG-410333 |
|
| | |
| | IMG-410335 |
|
| | Release the catch. Remove the marked part. |
| | IMG-410340 |
|
| | Remove the part carefully |
| | IMG-400000 |
|
| | Repeat the steps when removing on opposite side. |
| | IMG-410355 |
|
| | Raise the car. Remove the screws. |
| | IMG-413535 |
|
| | Note! This step requires the aid of another technician. |
Loosen the component indicated. Do not remove it. |
| | IMG-413541 |
|
| | Note! The number of connectors may vary depending on the vehicle's equipment level. |
Release the connector's catch. Disconnect the connector. |
| | IMG-413546 |
|
| | Caution! Place the Bumper Cover on a suitable surface. |
Remove the marked part. |
| | |
| | IMG-421093 |
|
| | Locate the markings for the positions. Measure and mark out the centre. Use: Scribe
|
| | IMG-421094 |
|
| | |
| | IMG-421095 |
|
| | Caution! Sharp end of tool must be on outside of cover. |
Use special tool: T9997234, Hole stamp
|
| | IMG-421096 |
|
| | Clean the surfaces. Use: , Isopropanol
|
| | IMG-421098 |
|
| | Note! Prepare and install one holder at a time. |
|
| | IMG-420220 |
|
| | |
| | IMG-420165 |
|
| | Clean the surface. Use: , Isopropanol
|
| | IMG-420166 |
|
| | Warning! Wear protective gloves. |
Warning! Make sure to provide adequate ventilation. |
Apply a thin and even layer. Use special tool: T9512950, Glue gun (kit)
Use: 1161730, Mixing pipe Use: 9511027, Glue
|
| | IMG-420219 |
|
| | |
| | IMG-420218 |
|
| | Note! Hold the part securely at the marker arrows when removing the tool. |
|
| | IMG-420216 |
|
| | |
| | IMG-421100 |
|
| | Disconnect the connectors. Attach the connector to the wiring harness. |
| | IMG-421101 |
|
| | Install component that comes with the accessory kit. Put the wiring in the Bumper cover without installing the wiring. |
| | IMG-420335 |
|
| | Connect the two painted sensors to the external connections. BN = Brown GY = Grey OG = Orange WH = White |
| | IMG-420337 |
|
| | BN = Brown GY = Grey WH = White YE = Yellow |
| | IMG-420338 |
|
| | Repeated on the right-hand side. |
| | IMG-421105 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-421106 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-421111 |
|
| | Note! This step is easier with two people. |
Place the Bumper Cover in position for installation. |
| | Vehicles without aftermarket-installed Parking assistance |
| | IMG-415410 |
|
| | |
| | Vehicles with aftermarket-installed Parking assistance |
| | IMG-420170 |
|
| | Loosen the component indicated. Do not remove it. |
| | IMG-420171 |
|
| | |
| | IMG-420173 |
|
| | Use special tool: T9814203, Expander pliers
|
| | IMG-416935 |
|
| | Remove the marked part. The part is not to be reused. |
| | IMG-420175 |
|
| | |
| | IMG-420362 |
|
| | |
| | |
| | IMG-415415 |
|
| | Route the wiring harness into the passenger compartment. |
| | IMG-415420 |
|
| | Caution! Make sure that the rubber grommet seals properly to the body. |
|
| | IMG-421112 |
|
| | |
| | |
| | IMG-421136 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-421143 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-421396 |
|
| | Reinstall the insulation mat. Reinstall the clips. |
| | IMG-421397 |
|
| | Connect the connector. Install the wiring harness. |
| | IMG-421144 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-421145 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-421146 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-420500 |
|
| | Position/route the cable as illustrated. Install the cable. Use a cable tie |
| | IMG-420502 |
|
| | Note! Route the wiring between floor carpet and air duct. |
Position/route the cable as illustrated. |
| | IMG-420504 |
|
| | Position/route the cable as illustrated. |
| | IMG-421281 |
|
| | |
| | IMG-421282 |
|
| | |
| | IMG-421283 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-420320 |
|
| | |
| | IMG-412677 |
|
| | Remove the clips. Remove the marked part. Repeat on the other side. |
| | IMG-412680 |
|
| | Remove the clip. Remove the marked part. Repeat on the other side. |
| | IMG-412681 |
|
| | |
| | IMG-403425 |
|
| | Remove the marked part. Use: Pliers
|
| | IMG-415975 |
|
| | Remove the screws. Remove the marked part. |
| | IMG-412692 |
|
| | Remove the clips. Remove the screws. |
| | IMG-412697 |
|
| | |
| | IMG-412710 |
|
| | Fold the wing liner aside. |
| | IMG-412715 |
|
| | |
| | IMG-400000 |
|
| | Repeat the steps when removing on opposite side. |
| | Applies to the right-hand side |
| | IMG-420880 |
|
| | |
| | IMG-420881 |
|
| | Remove the clip. Remove the nut. |
| | IMG-420883 |
|
| | |
| | Vehicles with headlamp washers |
| | IMG-412745 |
|
| | Warning! Be prepared to collect escaping fluid. |
Release the lock. Loosen the marked detail/details. |
| | IMG-412750 |
|
| | Warning! Be prepared to collect escaping fluid. |
Release the lock. Loosen the marked detail/details. Repeat on the other side. |
| | |
| | IMG-412730 |
|
| | Note! The number of connectors may vary depending on the vehicle's equipment level. |
Disconnect the connectors. |
| | IMG-420663 |
|
| | Remove the clips. Remove the screws. Remove the marked part. |
| | IMG-412725 |
|
| | |
| | IMG-412771 |
|
| | Caution! Place the Bumper Cover on a suitable surface. |
Note! This step is easier with two people. |
Release the catches. Remove the part carefully Remove the marked part. |
| | Concerns US and Canadian markets. |
| | IMG-420729 |
|
| | |
| | Applies to all markets, except USA and Canada |
| | IMG-420730 |
|
| | |
| | |
| | IMG-420744 |
|
| | Locate the markings for the positions. Mark the centre. Use: Scribe
|
| | IMG-420743 |
|
| | |
| | IMG-420735 |
|
| | Caution! Ensure that the marking is vertical. |
Use special tool: T9997614, Hole punch
|
| | IMG-420741 |
|
| | Caution! Sharp end of tool must be on outside of cover. |
|
| | IMG-420745 |
|
| | Clean the surfaces. Use: , Isopropanol
Allow to dry. |
| | IMG-420746 |
|
| | Apply a thin and even layer. Use: 1161765, Primer
Allow to dry for at least 2 minutes, but no more than 60minutes. |
| | IMG-420752 |
|
| | Clean the surfaces. Use: , Isopropanol
Allow to dry. |
| | IMG-420753 |
|
| | Apply a thin and even layer. Use: 1161765, Primer
Allow to dry for at least 2 minutes, but no more than 60minutes. |
| | IMG-420763 |
|
| | |
| | IMG-420820 |
|
| | Note! Prepare and install one holder at a time. |
Remove the protective film. |
| | IMG-420755 |
|
| | Warning! Wear protective gloves. |
Warning! Make sure to provide adequate ventilation. |
Apply a thin and even layer. Use special tool: T9512950, Glue gun (kit)
Use: 1161730, Mixing pipe Use: 9511027, Glue
|
| | IMG-420760 |
|
| | |
| | IMG-420761 |
|
| | |
| | IMG-420762 |
|
| | Remove the marked part. The part is not to be reused. Repeat on the other side. |
| | IMG-420765 |
|
| | |
| | IMG-420766 |
|
| | Repeat on the other side. |
| | IMG-420774 |
|
| | Loosen the wiring harness or move it to the side. |
| | IMG-420793 |
|
| | Release the catches. Remove the marked part. The part is not to be reused. |
| | IMG-420821 |
|
| | |
| | IMG-420822 |
|
| | |
| | IMG-420823 |
|
| | Install the wiring harness. |
| | IMG-420825 |
|
| | Put the wiring in the Bumper cover without installing the wiring. |
| | IMG-420033 |
|
| | Connect the two painted sensors to the external connections. |
| | IMG-420826 |
|
| | Repeat on the other side. |
| | IMG-420830 |
|
| | Repeat on the other side. Connect the connectors. |
| | Vehicle variant with cable harness |
| | IMG-420835 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
| | IMG-420845 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
| | IMG-420850 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
| | Vehicle variant without cable harness |
| | IMG-420870 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. Use a cable tie |
| | IMG-420871 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. |
| | IMG-420875 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. |
| | IMG-420876 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. Use a cable tie |
| | |
| | IMG-420878 |
|
| | |
| | IMG-420901 |
|
| | |
| | IMG-420900 |
|
| | Position the cable harness excess as illustrated. Install the wiring harness. Use a cable tie |
| | IMG-420905 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
| | IMG-420927 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
| | IMG-420928 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
| | IMG-420929 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. Use a cable tie |
| | IMG-421017 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. Use a cable tie |
| | IMG-421321 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. Use a cable tie |
| | IMG-421335 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. Use a cable tie |
| | IMG-421323 |
|
| | Remove the nut. Fold the insulation aside. |
| | IMG-402286 |
|
| | Make a cut in the insulation. |
| | IMG-421325 |
|
| | Remove the marked part. The part is not to be reused. |
| | IMG-421024 |
|
| | |
| | IMG-421025 |
|
| | |
| | IMG-421020 |
|
| | |
| | IMG-402238 |
|
| | Pull the wiring through. Use: 1161150, Lubricant
Use special tool: T9814204, Expander pliers
|
| | IMG-402275 |
|
| | Route the wiring harness into the passenger compartment. |
| | IMG-402277 |
|
| | Caution! Make sure that the rubber grommet seals properly to the body. |
Insert the cable in to the passenger compartment, adjust the cable length out into the engine compartment and secure the rubber grommet. |
| | IMG-421375 |
|
| | Refit the insulation. Install the nut. |
| | IMG-421030 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. Use a cable tie Pull the wiring through. |
| | IMG-386826 |
|
| | |
| | IMG-421272 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. Use a cable tie |
| | IMG-387085 |
|
| | |
| | IMG-387086 |
|
| | |
| | IMG-403400 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-387107 |
|
| | Release the catch. Remove the marked part. |
| | IMG-387123 |
|
| | Remove the screws. Remove the marked part. |
| | IMG-387398 |
|
| | Depress the locking device. Release the connector's catch. Disconnect the connector.
|
| | IMG-387423 |
|
| | Release the catches. Remove the marked part. |
| | IMG-400415 |
|
| | Release the connector's secondary lock. Lift approximately 2 mm. |
| | IMG-421037 |
|
| | |
| | IMG-387476 |
|
| | Connect the prerouted wiring harness. BN = Brown GN = Green GY = Grey OG = Orange WH = White YE = Yellow |
| | IMG-402395 |
|
| | |
| | IMG-400383 |
|
| | Depress the secondary lock. |
| | IMG-387424 |
|
| | Reinstall the removed part. |
| | IMG-387415 |
|
| | Depress the locking device. Release the connector's catch. Disconnect the connector.
|
| | IMG-387423 |
|
| | Release the catches. Remove the marked part. |
| | IMG-409615 |
|
| | Release the catches. Remove the marked part. |
| | IMG-409805 |
|
| | Use special tool: T9512632, Terminal removal tool (Color code: RED)
|
| | IMG-409625 |
|
| | Disconnect terminals from the connector, following the graphic. BN = Brown GN = Green GY = Grey OG = Orange WH = White YE = Yellow |
| | IMG-410553 |
|
| | |
| | IMG-421039 |
|
| | Connect the prerouted wiring harness. BN = Brown GN = Green GY = Grey OG = Orange WH = White YE = Yellow |
| | IMG-409561 |
|
| | |
| | IMG-409626 |
|
| | Depress the secondary lock. |
| | IMG-387424 |
|
| | Reinstall the removed part. |
| | IMG-387144 |
|
| | |
| | IMG-387145 |
|
| | Reinstall the removed part. Reinstall the screws. |
| | IMG-421285 |
|
| | Install the cables. Use a cable tie |
| | IMG-400005 |
|
| | Caution! A change to another tire size will cause changes in tire circumference. This will affect the Parking assistance pilot function. |
Check that the tire dimension stated in the vehicle configuration, corresponds to the actual tire dimension of the vehicle. If this does not correspond, download correct software. |
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number. |
| | |
| | IMG-400000 |
|
| | Reinstall the removed parts in reverse order. |