| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
|  | | IMG-400004 |
|
| | Caution!
Attach the antenna wires using tape. Cable ties or similar must not be used. |
Caution!
Observe caution when handling fibre optic cables. |
Caution!
Make sure that the fiber optic cables are not bent to a radius of less than 25 mm. |
|
| | |
|  | | IMG-400010 |
|
| | Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components. Used for accessory components.
|
| | |
|  | | IMG-361731 |
|
| | |
|  | | IMG-368970 |
|
| | |
|  | | IMG-370275 |
|
| | Remove the screw. Remove the marked part. |
|  | | IMG-368979 |
|
| | |
|  | | IMG-370274 |
|
| | |
|  | | IMG-369020 |
|
| | Repeat on the other side. |
| | Vehicles with heated rear seat |
|  | | IMG-369022 |
|
| | |
|  | | IMG-369029 |
|
| | Disconnect the connector. Repeat on the other side. |
| | |
|  | | IMG-372960 |
|
| | |
|  | | IMG-366386 |
|
| | |
|  | | IMG-366507 |
|
| | |
|  | | IMG-369055 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-369878 |
|
| | |
|  | | IMG-369034 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-369033 |
|
| | |
|  | | IMG-369048 |
|
| | |
|  | | IMG-369049 |
|
| | |
|  | | IMG-368833 |
|
| | |
|  | | IMG-449670 |
|
| | |
|  | | IMG-449672 |
|
| | |
|  | | IMG-360944 |
|
| | Repeat on the other side. |
|  | | IMG-360951 |
|
| | |
|  | | IMG-354954 |
|
| | |
|  | | IMG-449160 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-369939 |
|
| | |
|  | | IMG-449163 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-369944 |
|
| | |
|  | | IMG-366366 |
|
| | |
|  | | IMG-355946 |
|
| | |
|  | | IMG-449147 |
|
| | |
|  | | IMG-449153 |
|
| | |
|  | | IMG-373747 |
|
| | |
|  | | IMG-373748 |
|
| | Disconnect the connector. |
|  | | IMG-369934 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-369005 |
|
| | |
|  | | IMG-369090 |
|
| | |
|  | | IMG-461419 |
|
| | |
|  | | IMG-461420 |
|
| | Remove the marked detail/details. |
|  | | IMG-461421 |
|
| | Remove the screws.
Tightening torque: Front seat to body
, 40 Nm
|
|  | | IMG-461440 |
|
| | |
|  | | IMG-461444 |
|
| | Remove the marked detail/details. |
|  | | IMG-461449 |
|
| | Remove the screws.
Tightening torque: Front seat to body
, 40 Nm
|
|  | | IMG-400002 |
|
| | Remove the battery's negative cable. |
|  | | IMG-373198 |
|
| | |
|  | | IMG-329209 |
|
| | Loosen the screws. Disconnect the connector. |
|  | | IMG-382639 |
|
| | Disconnect the connector, if applicable. |
|  | | IMG-461416 |
|
| | Caution!
Be extra careful when removing or installing this component. |
|
|  | | IMG-461530 |
|
| | Remove the screws. Loosen the marked detail. |
| | Vehicles with High Performance Sound |
|  | | IMG-461942 |
|
| | Disconnect the connector. |
| | Vehicles with Premium Sound |
|  | | IMG-461922 |
|
| | Disconnect the connector. |
|  | | IMG-460609 |
|
| | |
| | |
|  | | IMG-460610 |
|
| | Loosen the tape temporarily. The item is to be reused. |
|  | | IMG-460611 |
|
| | |
|  | | IMG-460426 |
|
| |
Use special tool: T9512620, Stripping tool (for wiring)
|
|  | | IMG-460764 |
|
| | Use detail according to image. |
|  | | IMG-460428 |
|
| |
Use special tool: T9512620, Stripping tool (for wiring)
|
|  | | IMG-460373 |
|
| | |
|  | | IMG-460547 |
|
| |
Use special tool: T9512785, Crimping tool (included in 9512669)
|
|  | | IMG-460375 |
|
| | Caution!
Make sure that the surrounding components are protected from heat. |
Use special tool: T9512777, Hot-air gun
|
|  | | IMG-460376 |
|
| | |
|  | | IMG-460660 |
|
| | |
|  | | IMG-460520 |
|
| | |
|  | | IMG-461533 |
|
| | |
|  | | IMG-461553 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
|  | | IMG-461535 |
|
| | |
|  | | IMG-461560 |
|
| | Connect the ground cable. Reinstall the screw.
Tightening torque: M6
, 10 Nm
|
|  | | IMG-461592 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
|  | | IMG-461597 |
|
| | Fold the floor carpet back. |
|  | | IMG-461598 |
|
| | Caution!
Make sure that the fiber optic cables are not bent to a radius of less than 25 mm. |
Place the overlap of the cable mat under the amplifier. Reinstall the removed part. Reinstall the screws.
Tightening torque: M6
, 10 Nm
|
|  | | IMG-461604 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
|  | | IMG-461609 |
|
| | Loosen the marked detail. |
|  | | IMG-461612 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
|  | | IMG-461633 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
|  | | IMG-461635 |
|
| | Assemble components that come with the accessory kit. |
|  | | IMG-461675 |
|
| | Install the marked component. |
|  | | IMG-461664 |
|
| | Install components that come with the accessory kit. |
|  | | IMG-461683 |
|
| | |
|  | | IMG-461779 |
|
| | Use details according to image. |
|  | | IMG-461781 |
|
| | Assemble components that come with the accessory kit. Note the position. |
|  | | IMG-461785 |
|
| | |
|  | | IMG-461794 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
|  | | IMG-449835 |
|
| | |
|  | | IMG-461796 |
|
| | |
|  | | IMG-449876 |
|
| | |
|  | | IMG-461881 |
|
| | |
|  | | IMG-461830 |
|
| | Disconnect the connectors. |
|  | | IMG-461833 |
|
| | |
|  | | IMG-461834 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-461835 |
|
| | Remove the marked part. The part is not to be reused. |
|  | | IMG-461877 |
|
| | Install component that comes with the accessory kit. Install the screw.
Tightening torque: M6
, 10 Nm
|
|  | | IMG-461879 |
|
| | |
|  | | IMG-461807 |
|
| | Assemble components that come with the accessory kit. Depress the secondary lock. |
|  | | IMG-461880 |
|
| | |
| | Reinstall the removed parts in reverse order. |
|  | | IMG-400003 |
|
| | Reinstall the battery's negative cable.
Tightening torque: Battery cable for battery
, 6 Nm
|
|  | | IMG-400006 |
|
| | Order and download software according to VIDA/SOFTWARE. Order and download software according to: 31382168
Download software (application) for the accessory's function according to the service information in VIDA. Order and download software according to: 31330938
|
