Installation Instructions

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC60 2018
XC60 (18-) 2018

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
322073611.031664778
Fender extension (vehicles with variant code UF07)




 

Materials

Designation

Part number

Isopropanol

1161721

Primer

1161727


Equipment
IMG-268803
IMG-263203
IMG-425905
IMG-425896

IMG-421931

IMG-425895

IMG-430760


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Further information

2
IMG-400007
 

Note!
If a pending accessories installation include the removing and replacing of the bumper, this installation should be carried out first.

When installing, the car must retain a temperature of 20 degrees C.

After installation, the car must not be washed for 48 hours

 

Color symbols

3
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

 

Removal

4
IMG-403425
 

Remove the marked part.

Use: Pliers

5
IMG-426018
 

Remove the screws.

Remove the marked part.

6
IMG-430876
 

Remove the screws.

Remove the marked part.

The part is to be reused.

7
IMG-430810
 

Remove the clip.

Remove the screws.

The part is to be reused.

8
IMG-430812
 

Remove the nuts.

 

Vehicles with air suspension

9
IMG-430818
 

Loosen the clip.

 

All vehicles

10
IMG-430845
 

Remove the marked part.

The part is not to be reused.

11
IMG-430846
 

Loosen the clips.

12
IMG-430847
 

Remove the marked part.

The part is not to be reused.

13
IMG-430855
 

Remove any traces of glue.

Use: 1161721, Isopropanol

 

Vehicles with Parking assistance pilot

14
IMG-426050
 

Release the catches.

Loosen the component indicated. Do not remove it.

15
IMG-426070
 

Remove the marked part.

Use: Interior trim remover

The part is not to be reused.

 

All vehicles

 

Accessory installation

16
IMG-430898
 

Install component that comes with the accessory kit.

17
IMG-430812
 

Install the nuts

18
IMG-430810
 

Reinstall the screws.

Install the clip(s).

19
IMG-430876
 

Reinstall the removed part.

Reinstall the screws.

20
IMG-426078
 

Note!
Make sure that the template is correctly located.

Hold the component in the position shown.

Make a hole, using the tool indicated.

Remove the Special Tool.

21
IMG-426095
 

Note!
Make sure that the template is correctly located.

Hold the component in the position shown.

Make a hole, using the tool indicated.

Remove the Special Tool.

22
IMG-426105
 

Clean the surfaces.

Allow to dry.

Use: 1161721, Isopropanol

23
IMG-426103
 

Remove the screw.

24
IMG-426104
 

Install component that comes with the accessory kit.

Reinstall the screw.

25
IMG-426136
 

Note!
Note the position.

Install component that comes with the accessory kit.

26
IMG-426137
 

Note!
This step is easier with two people.

  1. Hold the component in the position shown.

  2. Use: Masking tape

Remove the marked part.

27
IMG-426165
 

Note!
Note the position.

Install component that comes with the accessory kit.

28
IMG-426166
 

Note!
This step is easier with two people.

  1. Hold the component in the position shown.

  2. Use: Masking tape

Remove the marked part.

29
IMG-426170
 

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

30
IMG-426175
 

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

 

Removal

31
IMG-430965
 

Remove the screws.

Remove the marked part.

The part is not to be reused.

32
IMG-426191
 

Note!
Make sure that the template is correctly located.

Hold the component in the position shown.

Make a hole, using the tool indicated.

Remove the Special Tool.

33
IMG-426185
 

Clean the surfaces.

Allow to dry.

Use: 1161721, Isopropanol

34
IMG-426260
 

Note!
Note the position.

Install component that comes with the accessory kit.

35
IMG-426262
 

Note!
This step is easier with two people.

  1. Hold the component in the position shown.

  2. Use: Masking tape

Remove the marked part.

36
IMG-426263
 

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

37
IMG-426270
 

Note!
Note the position.

Install component that comes with the accessory kit.

38
IMG-426275
 

Note!
This step is easier with two people.

  1. Hold the component in the position shown.

  2. Use: Masking tape

Remove the marked part.

39
IMG-426276
 

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

40
IMG-426280
 

Note!
Note the position.

Install component that comes with the accessory kit.

41
IMG-426281
 

Note!
This step is easier with two people.

  1. Hold the component in the position shown.

  2. Use: Masking tape

Remove the marked part.

42
IMG-426282
 

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

43
IMG-426310
 

Fold the protective film forward

 

Vehicles with Parking assistance pilot

44
IMG-431030
 

Remove the marked part.

The part is not to be reused.

 

All vehicles

45
IMG-426136
 

Note!
Note the position.

Install component that comes with the accessory kit.

46
IMG-426311
 

Caution!
Pull carefully.


Note!
Press and apply pressure to the part over the tape for at least 20 seconds.


Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

47
IMG-426395
 

Install component that comes with the accessory kit.

Secure the template with tape.

Use: Masking tape

48
IMG-426332
 

Fold the protective film forward

49
IMG-426396
 

Note!
Note the position.

Install component that comes with the accessory kit.

50
IMG-426335
 

Caution!
Pull carefully.


Note!
This step requires the aid of another technician.


Note!
Adjust the position of the components to create even spaces.

Remove the protective film.

51
IMG-430895
 

Remove the screw.

Remove the marked part.

Reinstall the screw.

52
IMG-430881
 

Caution!
Pull carefully.


Note!
Press and apply pressure to the part over the tape for at least 20 seconds.


Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

53
IMG-426400
 

Fold the protective film forward

54
IMG-426260
 

Note!
Note the position.

Install component that comes with the accessory kit.

55
IMG-426401
 

Caution!
Pull carefully.


Note!
Press and apply pressure to the part over the tape for at least 20 seconds.


Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

56
IMG-426405
 

Install component that comes with the accessory kit.

Secure the template with tape.

Use: Masking tape

57
IMG-426410
 

Fold the protective film forward

58
IMG-426426
 

Note!
Note the position.

Install component that comes with the accessory kit.

59
IMG-426420
 

Caution!
Pull carefully.


Note!
Press and apply pressure to the part over the tape for at least 20 seconds.


Note!
Adjust the position of the components to create even spaces.

Remove the protective film.

60
IMG-426430
 

Fold the protective film forward

61
IMG-426436
 

Note!
Adjust the position of the components to create even spaces.


Note!
Note the position.

Install component that comes with the accessory kit.

62
IMG-426435
 

Caution!
Pull carefully.


Note!
Press and apply pressure to the part over the tape for at least 20 seconds.


Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

 

When necessary, carry out the following instruction.

63
IMG-430970
 

Remove the screws.

64
IMG-420407
 

Fold the wing liner aside.

65
IMG-431010
 

Note!
Adjust the position of the components to create even spaces.

Loosen the screws.

66
IMG-382211
 

Fold the wing liner aside.

67
IMG-412715
 

Note!
Do not loosen the bolts more than one turn.

68
IMG-431020
 

Note!
Adjust the position of the components to create even spaces.

 

Installation

69
 

Reinstall the removed parts in reverse order.

 

Accessory installation

70
 

Repeat the steps when installing accessories on opposite side.