Installation Instructions

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC90 2016
XC90 (16-) 2016

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
314280681.331439261, 31414813
Sill molding, illuminated, rear




 

Special tools

 

999 5919 PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool number:999 5919

Tool description:PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool boards:46

 

951 2932 Tension spring

Tool number:951 2932

Tool description:Tension spring

Tool boards:80


Equipment
A0000162

IMG-437215


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Color symbols

2
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

 

Removal

3
IMG-394779
 
4
IMG-383040
 

Remove the marked part.

5
IMG-394727
 

Remove the marked part.

6
IMG-383066
 

Remove the marked part.

7
IMG-387004
 

Remove the marked part.

8
IMG-383047
 

Note!
Do not loosen the bolts more than 2 turns.

9
IMG-383048
 

Note!
The clips consist of two parts.

The part is not to be reused.

10
IMG-393950
 

Remove the clips.


Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

11
IMG-383043
 

Remove the marked part.

Remove the screw.


Tightening torque: Panel, to D-Pillar , 4.5 Nm

Repeat on the other side.

12
IMG-383044
 

Remove the panel.

Repeat on the other side.

13
IMG-383045
 

Remove the nut.

Repeat on the other side.

14
IMG-383046
 

Remove the panel.

Repeat on the other side.

 

Accessory installation

15
IMG-394786
 


Use special tool: T9512932, Tension spring

16
IMG-394795
 

Pull the wiring through.

Remove the tool.

17
IMG-394731
 

Disconnect the connector.

18
IMG-394736
 

Connect the connectors.

19
IMG-394742
 

Attach the connector to the wiring harness.

20
IMG-401498
 

Pull the wiring through.

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

21
IMG-401516
 

Pull the wiring through.

22
IMG-401509
 

Disconnect the connector.

23
IMG-401508
 

Connect the connectors.

24
IMG-401507
 

Attach the connector to the wiring harness.

25
IMG-437211
 
26
IMG-403005
 

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

27
IMG-403003
 

Release the connector's secondary lock.

Lift approximately 2 mm.

28
IMG-403042
 

Connect the prerouted cable.

29
IMG-403004
 

Depress the secondary lock.

30
IMG-401480
 

Connect the connector.

Install the cables.

31
IMG-394814
 
32
IMG-401492
 

Position the cable harness excess as illustrated.

Install the cables.

Use a cable tie

33
IMG-383047
 

Tighten the bolts.

34
IMG-437212
 

Remove the protective film.

 

Installation

35
 

Reinstall the removed parts in reverse order.