| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | When installing, the car must retain a temperature of 20 degrees C. |
| | |
|  | | IMG-363036 |
|
| | Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | |
|  | | IMG-394779 |
|
| | |
|  | | IMG-398662 |
|
| | Make sure that the components are not mixed up at the installation. Remove the marked part. Use hands only. Repeat on the other side. |
|  | | IMG-403002 |
|
| | |
|  | | IMG-385738 |
|
| | Fold the wing liner aside. |
|  | | IMG-402988 |
|
| | Remove the part carefully Release the catches. |
|  | | IMG-402987 |
|
| | Remove the part carefully Loosen the clips. |
|  | | IMG-402986 |
|
| | Remove the part carefully Remove the marked part. |
|  | | IMG-401258 |
|
| | Release the catches. Remove the part carefully |
|  | | IMG-392800 |
|
| | |
|  | | IMG-392801 |
|
| | |
|  | | IMG-377070 |
|
| | Repeat the steps when removing on opposite side. |
|  | | IMG-381918 |
|
| | Locate the connector. Release the connector's catch. Disconnect the connector. |
|  | | IMG-381901 |
|
| | |
|  | | IMG-381867 |
|
| | Caution!
Place the Bumper Cover on a suitable surface. |
Request the aid of a colleague for this procedure. Remove the marked part. |
|  | | IMG-381872 |
|
| | Remove the nuts. The part is not to be reused. Repeat on the other side. |
|  | | IMG-381912 |
|
| | The part is not to be reused. |
| | |
|  | | IMG-382024 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-381874 |
|
| | Install the nuts Repeat on the other side. |
|  | | IMG-386120 |
|
| | Install the screw. Repeat on the other side. |
|  | | IMG-386113 |
|
| | Install the nut. Repeat on the other side. |
|  | | IMG-399383 |
|
| |
Tightening torque: Tow hitch member mounting to body frame
Stage 1:
50 Nm
Stage 2:
30 Degree
Repeat on the other side. |
|  | | IMG-382038 |
|
| | Install component that comes with the accessory kit. Install the screws. Install the nuts |
|  | | IMG-386719 |
|
| | Fasten the wiring harness using the existing clips. Install component that comes with the accessory kit. |
|  | | IMG-390648 |
|
| | Note!
Make sure that the entire marked area is treated as indicated in graphic. |
Use: 30749880, Grease
On both sides. |
|  | | IMG-404149 |
|
| | Install component that comes with the accessory kit. |
| | |
|  | | IMG-383040 |
|
| | |
|  | | IMG-394727 |
|
| | |
|  | | IMG-381879 |
|
| | |
|  | | IMG-385592 |
|
| | Fold the insulation aside. |
|  | | IMG-385593 |
|
| | Locate the rubber grommet under the insulation and press it out. |
|  | | IMG-385583 |
|
| | The part is not to be reused. |
| | |
|  | | IMG-404145 |
|
| | Position/route the cable harness as illustrated. Route the wiring harness into the passenger compartment. |
|  | | IMG-358177 |
|
| | Caution!
Make sure that the rubber grommet seals properly to the body. |
|
| | |
|  | | IMG-404146 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. |
| | |
|  | | IMG-404147 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. |
| | |
|  | | IMG-404148 |
|
| | Position/route the cable harness as illustrated. Install the wiring harness. |
|  | | IMG-385805 |
|
| | |
| | |
|  | | IMG-385513 |
|
| | Release the catch. Remove the marked part. |
|  | | IMG-385668 |
|
| | |
| | |
|  | | IMG-393905 |
|
| | Route the cable harness to the existing cable harness. Install the cable. |
|  | | IMG-381883 |
|
| | Ground connection Connect the cable. Install the nut.
Tightening torque: M6
, 10 Nm
|
|  | | IMG-382156 |
|
| | Clean the surface. Use: 1161721, Isopropanol
Wipe dry. |
|  | | IMG-385629 |
|
| | Clean the surface. Use: 1161721, Isopropanol
Wipe dry. |
|  | | IMG-222282 |
|
| | |
|  | | IMG-241925 |
|
| | |
|  | | IMG-392341 |
|
| | |
|  | | IMG-392265 |
|
| | Connect the prerouted cables. |
|  | | IMG-393935 |
|
| | Locate the pre-routed connectors. |
|  | | IMG-396797 |
|
| | Disconnect the connector. The part is not to be reused. |
|  | | IMG-392270 |
|
| | |
|  | | IMG-392282 |
|
| | |
|  | | IMG-356352 |
|
| | Remove the protective film. |
|  | | IMG-381889 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-404150 |
|
| | Install component that comes with the accessory kit. |
| | |
|  | | IMG-392427 |
|
| | |
| | |
|  | | IMG-387079 |
|
| | |
| | |
| | |
|  | | IMG-387018 |
|
| | |
|  | | IMG-387032 |
|
| | Apply tape to the other side, opposite the marking lines. |
|  | | IMG-387035 |
|
| | Scribe/mark up Remove the marked part. Use: Air-powered air saw
|
|  | | IMG-387036 |
|
| | Deburr edges Remove the tape. |
| | |
|  | | IMG-386794 |
|
| | Release the catches. Use: Interior trim remover
Remove the panel. |
|  | | IMG-386814 |
|
| | Release the catches. Use: Interior trim remover
|
|  | | IMG-386819 |
|
| | Remove the panel. The part is to be reused. |
| | |
|  | | IMG-400605 |
|
| | Cut following the dotted lines. |
|  | | IMG-393972 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-401050 |
|
| | Reinstall the removed part. Repeat on the other side. |
| | |
|  | | IMG-396067 |
|
| | Place the component where indicated in the graphic. |
| | |
|  | | IMG-395285 |
|
| | Request the aid of a colleague for this procedure. Connect the connector. |
|  | | IMG-395286 |
|
| | Reinstall the bumper. Request the aid of a colleague for this procedure. |
|  | | IMG-402997 |
|
| | Note!
Make sure to follow the sequence indicated. |
Reinstall the removed part. Ensure that all clips engage. Repeat on the other side. |
| | | IMG-377070 |
|
| | Reinstall the removed parts in reverse order. |
|  | | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number. Order and download software according to: 31346719
|
| | |
|  | | IMG-384866 |
|
| | Warning!
Check for correct operation after the installation. |
Note!
To activate the trailer module (TRM) at least two light sources (lamps) must be connected. This can be done by connecting test equipment for the trailer connector, or a trailer. |
Note!
The trailer module (TRM) must be programmed with correct software to function correctly. |
7-pin connection Brake lamp/Left indicator Ground connection Spare slot (brake lamp, electrical trailer brake) Stop lamp/ Right turn signal lamp Charging Position lamp Spare (back-up light)
The wire for pin 3 for7-pin connection is blue (BL) The cable is secured at the wiring approximately 1 metre from the trailer connector. |
|  | | IMG-384862 |
|
| | 4-pin connection Stop lamp/ Right turn signal lamp Brake lamp/Left indicator Position lamp Ground connection
|
| | |
|  | | IMG-442138 |
|
| | Install component that comes with the accessory kit. Check that the component has locked in its position. |
|  | | IMG-401080 |
|
| | Note!
Ensure that the component is in contact with the surface, with no space. |
Install component that comes with the accessory kit. |
|  | | IMG-403008 |
|
| | Remove the part carefully |
|  | | IMG-403009 |
|
| | Use a drill with the stated size |
|  | | IMG-403011 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-442139 |
|
| | Install component that comes with the accessory kit. Check that the component has locked in its position. |
