| | |
| | IMG-240660 |
|
| | Removal For cars with fuel-driven parking heater installed. Drill out the three rivets from the front edge of the left wing liner. Remove the remains of the rivets. Move the wing liner aside and fasten it so that the parking heater is accessible.
|
| | IMG-231722 |
|
| | |
| | IMG-231723 |
|
| | |
| | IMG-231725 |
|
| | |
| | IMG-231682 |
|
| | |
| | IMG-231726 |
|
| | Drill a Ø29 mm (1 1/8 ") diameter hole using a hole saw according to the existing marking in the lower edge of the bumper cover. Pre-drill using a Ø3mm (1/8 ") diameter drill bit.
Note!
It is important that the hole is drilled right in the centre of the marking in order to correspond with the hole cut out earlier. |
Even out the hole edges and remove the drill swarf.
|
| | IMG-231727 |
|
| | |
| | IMG-231728 |
|
| | |
| | Installing the front engine block heater socket |
| | IMG-231729 |
|
| | Installing the front engine block heater socket Press the protective cover (from the kit) into place in the hole cut in the bumper cover. Insert the cable for the front engine block heater socket together with the ground lead from the kit through the protective cover.
|
| | IMG-231730 |
|
| | IMG-231731 |
|
| | Illustrations A and B Install the nut from the kit. Rotate the connector for the front engine block heater socket so that the cover opens backwards (Illustration B). Plug the electrical connector into the front engine block heater socket. Use the connector as a counterhold when tightening. Tighten the front engine block heater socket to the bumper cover. Remove the cover on the cooling system expansion tank.
|
| | IMG-373162 |
|
| | Drill a hole in the front/lower edge of the side member with a Ø5.5 mm bit. Apply anti-corrosion agent to the edges of the holes and secure the ground cable with the enclosed flanged screw and toothed washer.
Note!
Connect the ground cable to the side member, not to the subframe. |
Secure the excess ground cable length with a tie strap from the kit. Transfer the front intake's cable over the stay for the skid plate.
|
| | Installing the engine block heater |
| | IMG-231691 |
|
| | Installing the engine block heater |
| | IMG-231694 |
|
| | |
| | IMG-231697 |
|
| | |
| | IMG-231698 |
|
| | |
| | IMG-231699 |
|
| | |
| | IMG-231700 |
|
| | |
| | IMG-231703 |
|
| | Take a hose clamp from the kit and install it on the short hose end. Take the hose end and press it on the pipe that runs to the thermostat housing. Make sure that the cut-out in the hose connection is turned down and fits into the corresponding pin in the pipe connection. Rotate the catch on the pipe clockwise against the stop.
|
| | IMG-231478 |
|
| | Take the engine block heater, bracket, rubber coated clamp and screw from the kit and assemble them as illustrated. Do not tighten the screw yet.
|
| | IMG-231479 |
|
| | |
| | IMG-231480 |
|
| | Position the engine block heater with bracket in the front edge of the oil sump and connect the upper hose end to the engine block heater's connection. Take a screw from the kit and tighten the bracket with engine block heater into the existing hole in the oil sump.
Note!
The screw is self-tapping so inserting it may be slow. Make sure that the screw is centred straight into the hole, so that the screw head is flat against the bracket. |
|
| | IMG-231704 |
|
| | Now adjust the engine block heater in the rubber coated clamp so that the hoses are properly fitted on the engine block heater's connections. Tighten the screw to the rubber coated clamp. Tighten the hose clamps to the engine block heater.
|
| | IMG-240664 |
|
| | Take four double tie straps from the kit and secure them on the pipe and hose to the thermostat housing as well as the lower hose to the radiator. Check that the cable does not lie against sharp edges or moving parts in the engine compartment.
Caution!
Do not clamp the cable directly to brake pipes, fuel lines, AC pipes or pipes to the power steering. |
|
| | IMG-231706 |
|
| | |
| | D3601932 |
|
| | Take the joint cable from the kit. Grease in the O-ring on the connector on the cable to the front engine block heater socket, use low temperature grease P/N 1161427.
Note!
Do not get any grease on the surfaces of the connector. |
|
| | IMG-231707 |
|
| | |
| | IMG-373148 |
|
| | |
| | |
| | Finishing work For cars with fuel-driven heater: Reposition the left wing liner and rivet it in place. Fill with coolant, run the engine to operating temperature, bleed the cooling system and check that there are no leaks. Top up the cooling system as required. Reinstall the engine splash guard and torque tighten the screws to 25 Nm (18.5 lbf.ft.).
|