Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

7. Used for accessory components.

Removal

Loosen the marked detail.

Use special tool: T9997390, Key

Pull the component in direction of the arrow.

Depress the locking device.

Repeat on the other side.

Loosen the marked detail.

Disconnect the connectors.

Remove the marked part.

Remove the screws.

Release the catches.

Repeat on the other side.

Remove the panel.

Use: Interior trim remover

Remove the panel.

Release the catches.

Repeat on the other side.

Remove the panel.

Disconnect the connector.

Remove the marked part.

Loosen the marked detail.

Loosen the marked detail.

Remove the marked part.

Remove the marked part.

Remove the screws.

Tightening torque: M5 , 5 Nm

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Remove the marked part.

Remove the screw.

Tightening torque: Panel A-pillar , 4.5 Nm

Remove the panel.

Remove the screws.

Tightening torque: Entry handle, to bracket , 6 Nm

Remove the marked parts.

Remove the part carefully

Repeat on the other side.

Remove the marked part.

Remove the marked part.

Reinstall the screw.

Tightening torque: Panel, to C pillar , 4.5 Nm

The graphic shows the back of the component.

Remove the panel.

Loosen the fastener.

Use special tool: T9997390, Key

Remove the part carefully

Fold marked part aside.

Remove the panel.

Loosen the marked detail.

Release the catches.

Loosen the marked detail.

Accessory installation

Clean the marked area.

Use: , Isopropanol

Measure and mark as illustrated.

Use: , Masking tape

Remove the protective film.

Install components that come with the accessory kit.

Install components that come with the accessory kit.

Install the screws.

Install components that come with the accessory kit.

Use: 988734, Cable tie, 750 mm

Use: , Electrical tape

Pull the wiring through.

Position/route the cable as illustrated.

Connect the connector.

Position/route the cable as illustrated.

Apply tape.

Reinstall the removed part.

To be repeated in the other end of the component.

Reinstall the removed part.

To be repeated in the other end of the component.

Position/route the cables as illustrated.

Install the cable.

Apply tape.

Position/route the cable as illustrated.

Install the cable.

Apply tape.

Position/route the cable as illustrated.

Measure

Position/route the cable as illustrated.

Position the cable harness excess as illustrated.

Install the cable.

Apply tape.

Assemble components that come with the accessory kit.

Reinstall the removed part.

Install component that comes with the accessory kit.

Rotate marked component according to image.

Connect the prerouted cable.

Connect the connector.

Installation

Reinstall the removed parts in reverse order.

Adjustment

Adjust the camera angle outside.

Make sure there is 20-30 meters of clear rear view.

Tighten the bolts.

Install components that come with the accessory kit.

Install components that come with the accessory kit.

Tighten the bolts.