| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | Disconnecting the battery |
| | IMG-394535 |
|
| | |
| | IMG-410210 |
|
| | |
| | IMG-421699 |
|
| | |
| | IMG-394520 |
|
| | Remove the battery's negative cable. |
| | |
| | IMG-411195 |
|
| | |
| | Vehicles with spare wheel |
| | IMG-411295 |
|
| | |
| | IMG-411296 |
|
| | |
| | |
| | IMG-411216 |
|
| | Remove the part carefully Use: Interior trim remover
|
| | IMG-411217 |
|
| | Disconnect the connector. Remove the marked part. |
| | Vehicles with keyless entry |
| | IMG-413321 |
|
| | Release the catch. Fold marked part aside.
|
| | |
| | IMG-411205 |
|
| | Remove the screw. Tightening torque: M8
, 24 Nm
Remove the marked part. Repeat on the other side. |
| | IMG-411220 |
|
| | Remove the nut. Tightening torque: M6
, 10 Nm
Use special tool: T9997606, Sleeve
Repeat on the other side. |
| | IMG-414161 |
|
| | |
| | IMG-415786 |
|
| | |
| | IMG-411342 |
|
| | |
| | IMG-411349 |
|
| | |
| | IMG-411350 |
|
| | Remove the marked part. Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304
|
| | IMG-411351 |
|
| | Remove the screw. Tightening torque: M8
, 24 Nm
|
| | IMG-410550 |
|
| | |
| | IMG-411322 |
|
| | Remove the clip. Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones. |
| | IMG-411355 |
|
| | |
| | IMG-417874 |
|
| | |
| | IMG-414370 |
|
| | |
| | |
| | IMG-414065 |
|
| | |
| | IMG-414066 |
|
| | Measure and mark as illustrated. Remove the marked part.
|
| | IMG-414068 |
|
| | Install component that comes with the accessory kit. |
| | IMG-414055 |
|
| | Clean the surface. Use: , Isopropanol
Wipe dry. |
| | IMG-414056 |
|
| | Clean the surface. Use: , Isopropanol
Wipe dry. |
| | IMG-414059 |
|
| | |
| | IMG-241925 |
|
| | Remove the protective film. |
| | IMG-414060 |
|
| | Measure Install component that comes with the accessory kit. |
| | IMG-356352 |
|
| | Remove the protective film. |
| | IMG-414058 |
|
| | Note! Ensure that the tape is fixed to the surface. |
Install component that comes with the accessory kit. |
| | |
| | IMG-410325 |
|
| | |
| | IMG-410326 |
|
| | Fold the wing liner aside. |
| | IMG-410333 |
|
| | |
| | IMG-410335 |
|
| | Release the catch. Remove the marked part. |
| | IMG-410340 |
|
| | Remove the part carefully |
| | Repeat the steps when removing on opposite side. |
| | IMG-410355 |
|
| | |
| | IMG-410352 |
|
| | Note! This step requires the aid of another technician. |
Loosen the component indicated. Do not remove it. |
| | IMG-410370 |
|
| | Note! The number of connectors may vary depending on the vehicle's equipment level. |
Release the connector's catch. Disconnect the connector. |
| | Vehicles with Parking assistance camera |
| | IMG-410371 |
|
| | Release the connector's catch. Disconnect the connector. |
| | |
| | IMG-410372 |
|
| | Caution! Place the Bumper Cover on a suitable surface. |
Note! This step requires the aid of another technician. |
Remove the marked part. |
| | |
| | IMG-410979 |
|
| | |
| | IMG-413287 |
|
| | Make a hole, using the tool indicated. |
| | IMG-410992 |
|
| | Apply tape to the other side, opposite the marking lines. Use: , Masking tape
|
| | IMG-410981 |
|
| | Mark using a pen Remove the marked part.
Use: Air-powered air saw
|
| | IMG-410983 |
|
| | |
| | IMG-414020 |
|
| | Remove the marked part. Use: Air-powered air saw
|
| | |
| | IMG-410526 |
|
| | Remove the nuts. The part is to be reused. Repeat on the other side. |
| | IMG-410527 |
|
| | Remove the marked part. The part is not to be reused. |
| | IMG-410533 |
|
| | Remove the marked part. Use: Interior trim remover
The part is not to be reused. |
| | |
| | IMG-414030 |
|
| | Install component that comes with the accessory kit. |
| | IMG-472871 |
|
| | Install the nuts Repeat on the other side. |
| | IMG-405908 |
|
| | Install component that comes with the accessory kit. Repeat on the other side. |
| | IMG-414036 |
|
| | Tighten the nuts. Tighten the screw. Tightening torque: Tow hitch member mounting to body frame Stage 1:
50 Nm Stage 2:
30 Degree
Repeat on the other side. |
| | IMG-420756 |
|
| | Apply the stated Material on the marked surface. Repeat on the other side. Use: , Rust inhibitor
|
| | IMG-414071 |
|
| | Note! Make sure that the wire or wiring harness is not twisted. |
Route the wiring harness into the passenger compartment. |
| | IMG-358177 |
|
| | Caution! Make sure that the rubber grommet seals properly to the body. |
|
| | Vehicles with Twin Engine |
| | IMG-433966 |
|
| | |
| | IMG-433967 |
|
| | Position wire as illustrated. Install the wiring harness. |
| | Applies to all other vehicles |
| | IMG-414072 |
|
| | Position/route the cable as illustrated. Fasten the wiring harness using the existing clips. |
| | |
| | IMG-414073 |
|
| | Route the cable harness to the existing cable harness. Fasten the wiring harness using the existing clips. |
| | IMG-414083 |
|
| | Position/route the cable as illustrated. |
| | IMG-414084 |
|
| | Connect the prerouted cables. |
| | IMG-414085 |
|
| | Locate the pre-routed connectors. Connect the connectors. |
| | IMG-414086 |
|
| | The part is to be reused. Remove the nut. |
| | IMG-414087 |
|
| | Connect the prerouted cable. Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-414091 |
|
| | Release the lock. Remove the marked part.
|
| | IMG-493636 |
|
| | Install component that comes with the accessory kit. |
| | IMG-493637 |
|
| | Note! If position DF18 is occupied, ensure that a 40A fuse is mounted. |
Install component that comes with the accessory kit. |
| | IMG-414092 |
|
| | Reinstall the removed part. |
| | IMG-414093 |
|
| | Connect the prerouted cable. |
| | |
| | Reinstall the removed parts in reverse order. |
| | |
| | IMG-394580 |
|
| | Reinstall the battery's negative cable. Tightening torque: Battery cable for battery
, 6 Nm
|
| | |
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. Order and download software according to: 31435639
|
| | |
| | IMG-414094 |
|
| | |
| | IMG-414300 |
|
| | |
| | IMG-419240 |
|
| | If the components rub against each other, adjustments must be made to correct this. |
| | IMG-348017 |
|
| | Warning! Check for correct operation after the installation. |
Note! To activate the trailer module (TRM) at least two light sources (lamps) must be connected. This can be done by connecting test equipment for the trailer connector, or a trailer. |
Note! The trailer module (TRM) must be programmed with correct software to function correctly. |
Left indicator lamp Fog tail lamps. Ground connection Right indicator lamp Right position lamp Brake light Left position lamp Back-up lamp Battery voltage, constant Battery voltage, ignition on Ground connection Not connected Ground connection
|
| | IMG-414094 |
|
| | |
| | IMG-414301 |
|
| | |