Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

These installation instructions show installation on left hand drive cars.

When installing on right-hand drive cars, perform the procedures on the opposite side and/or mirrored.

Where the procedure differs, the right-hand version is also shown with text and image.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Removal

Set the ignition key to position 0.

Remove the panel.

Remove the weatherstrip.

Fold the carpet to the side.

Locate the rubber grommet under the insulation and press it out.

Repeat on the other side.

Disconnect the connector, if applicable.

Repeat on the other side.

Remove the panel.

Remove the weatherstrips.

Detach the panel.

Detach the panel.

Remove the nuts.

Remove the clips.

Remove the panel.

Turn the wheel inwards.

Remove the screws.

Vehicles with headlamp washers

Fold the wing liner to one side.

1. 
   

   Note! Tape the hose high up on the washer fluid reservoir to prevent washer fluid from coming out.

   
   

2. Take a piece of washer hose. Tie a knot in it and place it on the washer pump to prevent the washer fluid reservoir from emptying.

All vehicles

Turn the wheel inwards.

Remove the screws.

Fold the wing liner to one side.

Locate the connector.

1. Depress the locking device.

2. Disconnect the connector.

RHD: The procedure is carried out on the opposite side.

RHD: The procedure is carried out on the opposite side.

Remove the clips.

Remove the clips.

Remove the screws.

Repeat on the other side.

The part is not to be reused.

Remove the screws.

Remove the clips.

Repeat on the other side.

The part is not to be reused.

Accessory installation

Repeat on the other side.

Repeat on the other side.

Repeat on the other side.

RHD: The cable harness is positioned mirrored.

Connect the connectors.

Attach the connector to the wiring harness.

The connector is not to be used.

Repeat on the other side.

Left hand drive vehicles

Use: , Electrical tape

Right-hand drive vehicles

Use: , Electrical tape

All vehicles

Place the Bumper Cover in position for installation.

Left hand drive vehicles

Connect the connectors.

Right-hand drive vehicles

Connect the connector.

Connect the connector.

Vehicles with headlamp washers

Reinstall the removed parts in reverse order.

All vehicles

Reinstall the bumper.

Left hand drive vehicles

Route the cable harness to the existing cable harness.

Reinstall the headlamp.

Remove the nuts.

Pull the wiring through.

Install the cable.

Right-hand drive vehicles

Install the cable.

All vehicles

Pull the wiring through.

Insert the cable in to the passenger compartment, adjust the cable length out into the engine compartment and secure the rubber grommet.

Right-hand drive vehicles

All vehicles

Left hand drive vehicles

Connect the cable harness terminals in the connector as follows.

Right-hand drive vehicles

Connect the cable harness terminals in the connector as follows.

All vehicles

Disconnect the connector, if applicable.

Attach the connector to the wiring harness.

Use: , Electrical tape

The connector is not to be used.

Disconnect the connectors.

The part is not to be reused.

Install component that comes with the accessory kit.

Connect the connectors.

Connect the prerouted cable.

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31266964

Reinstall the removed parts in reverse order.