Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

7. Used for accessory components.

Removal

Repeat on the other side.

Remove the marked part.

Disconnect any connector(s).

Loosen the marked detail.

Loosen the marked detail.

Remove the marked part.

Remove the panel.

Remove the screw.

Remove the panel.

Detach the panel.

Remove the marked part.

Detach the panel.

Fold the carpet aside.

Remove the panel.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

Remove the panel.

Remove the screws.

Remove the screw.

Remove the marked part.

Remove the marked part.

Remove the screws.

Remove the panel.

Remove the panel.

Disconnect the connector.

Vehicles with TV-receiver

Replace rear right side window according to VIDA service information.

Information/ Repair/ Removal, replacement, installation/ 8 Body and interior/ 84 Exterior trim, glass, weatherstrips/ 844 glass for side doors and window/ Fixed side window

The connector is not to be used.

Use tape

All vehicles

Remove the panel.

Disconnect the connector, if applicable.

Remove the weatherstrip.

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Remove the battery's negative cable.

Alternative 1

Alternative 2

All vehicles

Loosen the screws.

Disconnect the connector.

Disconnect the connector, if applicable.

Remove the screws.

Loosen the marked detail.

Vehicles with High Performance Sound

Disconnect the connector.

Vehicles with Premium Sound

Disconnect the connector.

All vehicles

Accessory installation

Loosen the tape temporarily.

The item is to be reused.

Use special tool: T9512620, Stripping tool (for wiring)

Use detail according to image.

Use special tool: T9512620, Stripping tool (for wiring)

Use special tool: T9512785, Crimping tool (included in 9512669)

Use special tool: T9512777, Hot-air gun

Connect the connectors.

Fold the carpet aside.

Remove the screw.

Connect the ground cable.

Reinstall the screw.

Route the cable harness to the existing cable harness.

Install the wiring harness.

Use a cable tie

Route the cable harness to the existing cable harness.

Install the wiring harness.

Use a cable tie

Fold the floor carpet back.

Place the overlap of the cable mat under the amplifier.

Reinstall the removed part.

Reinstall the screws.

Tightening torque: M6 , 10 Nm

Assemble components that come with the accessory kit.

Install component that comes with the accessory kit.

Install component that comes with the accessory kit.

Fold the insulation aside.

Route the cable harness to the existing cable harness.

Install the wiring harness.

Use a cable tie

Pull the wiring harness through.

Refit the insulation.

Connect the connectors.

Removal

Remove the clips.

Remove the marked part.

Vehicles with TV-receiver

Remove the marked part.

Vehicles with TV-receiver

Disconnect the connectors.

Remove the screw.

Remove the marked part.

All vehicles

Accessory installation

Install components that come with the accessory kit.

Tightening torque: M6 , 10 Nm

Connect the connector.

Use details according to image.

Assemble components that come with the accessory kit.

Depress the secondary lock.

Vehicles with TV-receiver

Connect the connector.

Install component that comes with the accessory kit.

Vehicles with TV-receiver

Install component that comes with the accessory kit.

All vehicles

Route the wire adjacent to existing wirings.

Install the cable.

Use tape

Route the wire adjacent to existing wirings.

Install the cable.

Use tape

Fold the insulation aside.

Route the wire adjacent to existing wirings.

Install the cable.

Use tape

Pull the wiring harness through.

Refit the insulation.

Connect the connector.

Position the cable harness excess as illustrated.

Install the wiring harness.

Use tape

Reinstall the removed parts in reverse order.

Reinstall the battery's negative cable.

Order and download software according to VIDA/SOFTWARE.

Order and download software according to: 31268617

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31285168