Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

There may be parts in the accessories kit that are not needed for this installation.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Remove the panel.

Fold the carpet aside.

Unhook the cable harness clips.

Disconnect the connector.

Remove the panel.

Disconnect the connector, if applicable.

Disconnect the connector.

Remove the screws.

Remove the screws.

Cars with automatic transmissions

Remove the marked part.

Release the shift-lock function.

All vehicles

Disconnect the connector.

Remove the screws.

Remove the marked part.

Remove the marked part.

Accessory installation

Installation

Reinstall the removed part.

Reinstall the screws.

Removal

Vehicles with Sensus Connect

Remove the marked part.

Remove the screws.

Disconnect the connectors.

Disconnect the connector, if applicable.

The connector is not to be used.

Attach the connector to the wiring harness.

Use: , Electrical tape

Vehicles without Sensus Connect

Carefully pry loose the bottom edge of the panel and then continue around the panel.

Remove the screws.

Remove the marked part.

Disconnect the connector.

The connector is not to be used.

Attach the connector to the wiring harness.

Use: , Electrical tape

Disconnect the connectors.

All vehicles

Remove the panel.

Disconnect the connector, if applicable.

Remove the screws.

Detach the panel.

Disconnect the connector.

Remove the panel.

Remove the screws.

Remove the screws.

Note the position.

Disconnect the connector.

Unhook the cable harness clips.

Remove the marked part.

Remove the panel.

Remove the screw.

Remove the marked part.

Remove the weatherstrip.

Detach the panel.

Repeat on the other side.

Disconnect the connector, if applicable.

Repeat on the other side.

Remove the panel.

Remove the panel.

Remove the screw.

Remove the screw.

Remove the panel.

Remove the weatherstrips.

Remove the panel.

Remove the screws.

Remove the panel.

Remove the panel.

Remove the panel.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

Remove the panel.

Remove the screws.

Remove the panel.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

Remove the screw.

Detach the panel.

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Remove the screws.

Remove the panel.

Disconnect the connector, if applicable.

Loosen the clips.

Fold the insulation aside.

Use special tool: T9814088, Puller

Remove the screws.

Disconnect the connector.

Remove the marked part.

Remove the panel.

Remove the panel.

Repeat on the other side.

Use special tool: T9997390, Key

Remove the panel.

Disconnect the connectors.

Remove the screws.

Remove the marked part.

Remove the nuts.

Release the catches.

Release the catches.

Remove the marked part.

Accessory installation

Ensure that all clips engage.

Install the nuts

Tightening torque: Exterior handle to tailgate/luggage compartment lid , 3 Nm

Reinstall the removed part.

Reinstall the screws.

Connect the connectors.

Remove the part carefully

Use special tool: T9512932, Tension spring

Install the cable.

Use: , Electrical tape

Pull the wiring through.

Pull the wiring through.

Pull the wiring through.

Remove the Special Tool.

Connect the cable harness terminals in the connector as follows.

Depress the secondary lock.

Connect the connector.

Install the cable.

Use a cable tie

Adjust the position of the wiring.

Install the cable.

Use a cable tie

Adjust the position of the wiring.

Install the cable.

Use a cable tie

Reinstall the removed part.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Position/route the cable as illustrated.

Fold the insulation aside.

Position/route the cable as illustrated.

Pull the wiring through.

Fold the insulation aside.

Position/route the cable as illustrated.

Position/route the cable as illustrated.

Position/route the cable as illustrated.

Position/route the cable as illustrated.

Vehicles with Sensus Connect

Position/route the cable harness as illustrated.

Vehicles without Sensus Connect

Position/route the cable harness as illustrated.

Connect the connectors.

Connect the prerouted cable.

Reinstall the removed part.

Reinstall the screws.

All vehicles

Position/route the cable as illustrated.

Position/route the cable as illustrated.

1. Depress the locking device.

2. Release the connector's catch.

3. Disconnect the connector.

Release the catches.

Remove the marked part.

Release the connector's secondary lock.

Lift approximately 2 mm.

Connect the cable harness terminals in the connector as follows.

Depress the secondary lock.

Reinstall the removed part.

Connect the connector.

Install the cable.

Use a cable tie

Vehicles with Sensus Connect

Connect the prerouted cable.

Connect the connectors.

Reinstall the removed part.

Reinstall the screws.

All vehicles

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.

Calibrate according to: DIAGNOSTICS/VEHICLE COMMUNICATION/Advanced/PAC/Service calibration, parking camera