Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

There may be parts in the accessories kit that are not needed for this installation.

Disconnecting the battery

Set the vehicle to Inactive mode.

Remove the battery's negative cable.

Removal

Open the hood.

Remove the clips.

Remove the marked part.

Remove the screw.

Remove the screws.

Remove the marked part.

Vehicles with diesel engines

Loosen the marked detail.

Remove the clips.

Remove the marked part.

All vehicles

Remove the marked detail/details.

Use: Pliers 31423632

Remove the screws.

Remove the marked part.

Remove the clips.

Remove the screws.

Remove the nut.

Remove the screws.

Remove the nut.

Remove the clip.

Remove the marked part.

Remove the cable harness clips.

Loosen the screws.

Remove the marked part.

Fold marked part aside.

Remove the screws.

Remove the marked part.

Accessory installation

Locate relevant marking.

Use: Air-powered air saw

Install component that comes with the accessory kit.

Check that the flange of the part is in full contact with bumper cover.

Adjust the hole with a file or knife as necessary.

Pull the wiring through.

Note the position.

Assemble components that come with the accessory kit.

Install component that comes with the accessory kit.

This is used as a counterhold.

Tighten the nut.

Use hands only.

Use detail according to image.

Pull the wiring through.

Pull the wiring through.

Vehicles with diesel engines

All vehicles

Pull the wiring through.

Install components that come with the accessory kit.

Assemble components that come with the accessory kit.

Assemble components that come with the accessory kit.

Pull the wiring harness through.

Lubricate the O-ring.

Use: 1161427, Low temperature grease

Connect the cable.

Install the catch.

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Position/route the wiring harness as illustrated.

Install the wiring harness.

Use a cable tie

Pull the wiring harness through.

Lower the vehicle.

Pull the wiring harness through.

Position/route the wiring harness as illustrated.

Install the wiring harness.

Use a cable tie

RD = Red

BK = Black

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Position/route the cable as illustrated.

Remove the nut.

Connect the prerouted cable.

Install the nut.

Tightening torque: Nut (M8), to BCSM , 24 Nm

Pull the wiring through.

Install the wiring harness.

Use a cable tie

Raise the car.

Ground connection

Remove the nut.

Release the catches.

Loosen the marked detail.

Connect the prerouted cables.

Install the marked component.

Ensure that all clips engage.

Install the nut.

Tightening torque: M6 , 10 Nm

Lubricate the O-ring.

Use: 1161427, Low temperature grease

Reinstall the removed part.

Reinstall the screws.

Reinstall the removed part.

Reinstall the removed part.

Reinstall the screws.

Reinstall the removed part.

Connect the cable.

Install the catch.

Install the wiring harness.

Use a cable tie

Installation

Reinstall the removed parts in reverse order.

Tightening torque: Aluminum wheel rim to wheel hub
Stage 1: 4 Nm
Stage 2: 50 Nm
Stage 3: 140 Nm

Reinstall the battery's negative cable.