Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC60 2017
XC60 (-17) 2017

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313993441.031373090
Parking assistance, rear




 

Special tools

 

999 5919 PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool number:999 5919

Tool description:PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool boards:46

 

999 7234 Hole stamp

Tool number:999 7234

Tool description:Hole stamp

Tool boards:80

 

999 7483 Hole punch

Tool number:999 7483

Tool description:Hole punch

Tool boards:80

 

951 2950 Glue gun (kit)

Tool number:951 2950

Tool description:Glue gun (kit)

Tool boards:08


Materials

Designation

Part number

Masking tape

Isopropanol

1161721

Bonding primer, plastic

31335448

Sand paper P1000

Volvo Original Touch-up paint

Varnish 2-component

31335447

Activator

8637076

Mixing pipe

1161730

Glue

9511027


Equipment
IMG-242205
IMG-345497
IMG-239664
IMG-239981

IMG-377463

IMG-377443


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Further information

2
 

After installation, the car must not be washed for 48 hours

When installing, the car must retain a temperature of 20 degrees C.

 

Paintwork

3
IMG-377265
 

Use: , Masking tape

4
IMG-377266
 

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

5
IMG-377267
 

Use: 31335448, Bonding primer, plastic

Also see the instructions on the container.

6
IMG-377194
 
7
IMG-352653
 

Clean the surface.

8
IMG-352654
 

Matt the surface gently.

Use: , Sand paper P1000

9
IMG-352653
 

Clean the surface.

Allow to dry.

10
IMG-352655
 

Caution!
Protect connector surfaces against paint spray.


Note!
Use correct color following the vehicle's paint code.

Use: , Volvo Original Touch-up paint

Use base coat only.

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

11
IMG-377267
 

Note!
Use correct color following the vehicle's paint code.

Use: , Volvo Original Touch-up paint

Use base coat only.

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

12
IMG-352658
 

Caution!
First the paint must dry after painting.

13
IMG-377265
 

Remove the tape.

 

Removal

14
IMG-332193
 

Set the ignition key to position 0.

15
IMG-377269
 

Note!
Orientation view

16
IMG-372212
 

Measure and mark as illustrated.

17
IMG-372210
 
18
IMG-372209
 


Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

19
IMG-372207
 
 

Accessory installation

20
IMG-372208
 
 

Removal

21
IMG-377070
 

Note!
The removal steps may contain installation details.

22
IMG-377298
 
23
IMG-377299
 
24
IMG-377300
 
25
IMG-377302
 
26
IMG-377309
 

Remove the screw.

27
IMG-377320
 

Remove the panel.

28
IMG-343420
 

Remove the panel.

29
IMG-377345
 

Detach the panel.

30
IMG-377347
 

Release the catches.

Remove the panel.

31
IMG-307608
 
32
IMG-307609
 
33
IMG-377342
 

Remove the screws.


Tightening torque: M8 , 24 Nm

34
IMG-346921
 
35
IMG-346811
 
36
IMG-346861
 

Remove the screws.

Remove the panel.

37
IMG-377350
 

Detach the panel.

38
IMG-377352
 

Remove the panel.

39
IMG-297185
 
40
IMG-377456
 
41
IMG-379308
 

Remove the screws.

Repeat on the other side.

42
IMG-379313
 

Repeat on the other side.

43
IMG-379304
 

Disconnect the connector.

44
IMG-379314
 

Caution!
Place the Bumper Cover on a suitable surface.

45
IMG-377368
 

Disconnect the connectors.

Unhook the cable harness clips.

The cable harness must not be reused.

46
IMG-377371
 
47
IMG-377369
 

Release the catches.

48
IMG-377372
 
 

Accessory installation

49
IMG-377374
 

Locate the markings for the positions.

50
IMG-377375
 

Mark the centre.

51
IMG-377377
 
52
IMG-331348
 

Drill horizontally.

53
IMG-377378
 

Caution!
Sharp end of tool must be on outside of cover.


Use special tool: T9997234, Hole stamp

54
IMG-379343
 

Caution!
Sharp end of tool must be on outside of cover.


Note!
Check that the markings are opposite each other and that they are pointing downwards when the tool is used.


Use special tool: T9997483, Hole punch

55
IMG-377382
 

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

56
IMG-377398
 

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

57
IMG-377416
 

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

58
IMG-377385
 

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

59
IMG-377386
 

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

60
IMG-377400
 

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

61
IMG-377417
 

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

 

Removal

62
IMG-308085
 
63
IMG-308086
 
64
IMG-297561
 

Disconnect the connector.

Unhook the cable harness clips.

65
IMG-297562
 

The cable harness must not be reused.

 

Accessory installation

66
IMG-377427
 
67
IMG-377426
 
68
IMG-377425
 
69
IMG-297565
 

Locate the existing connector in the vehicle's cable harness.

Connect the connector.

70
IMG-377428
 

Install the cable.

Connect the connectors.

71
IMG-377429
 

Note!
Prepare and install one holder at a time.

72
IMG-377401
 

Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

73
IMG-377421
 

Warning!
Wear protective gloves.


Warning!
Make sure to provide adequate ventilation.

Apply a thin and even layer.


Use special tool: T9512950, Glue gun (kit)

Use: 1161730, Mixing pipe

Use: 9511027, Glue

74
IMG-297571
 
75
IMG-297572
 

Note!
Apply pressure only where the tape is located.


Note!
Ensure that the tape is fixed to the surface.

76
IMG-297573
 

Note!
Hold the part securely at the marker arrows when removing the tool.

77
IMG-377418
 

Note!
Prepare and install one holder at a time.


Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

78
IMG-377420
 

Warning!
Wear protective gloves.


Warning!
Make sure to provide adequate ventilation.

Apply a thin and even layer.


Use special tool: T9512950, Glue gun (kit)

Use: 1161730, Mixing pipe

Use: 9511027, Glue

79
IMG-297576
 

Note!
Apply pressure only where the tape is located.


Note!
Ensure that the tape is fixed to the surface.

80
IMG-377430
 

Reinstall the removed part.

81
IMG-377436
 

Reinstall the removed part.

82
IMG-377431
 

Install the cable.

Connect the connectors.

83
IMG-373743
 
84
IMG-377435
 
85
IMG-379305
 

Place the Bumper Cover in position for installation.

Connect the connector.

86
IMG-379307
 

Reinstall the bumper.

87
IMG-377070
 

Reinstall the removed parts in reverse order.

88
IMG-242268
 

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31266966