Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S60 2012
S60 (11-18) 2012

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313303711.431359220, 31339967, 31330366
Parking assistance, rear, R-design




 

Special tools

 

999 7234 Hole stamp

Tool number:999 7234

Tool description:Hole stamp

Tool boards:80


Materials

Designation

Part number

Isopropanol

1161721

Sand paper P1000

Volvo Original Touch-up paint

Varnish 2-component

31335447

Activator

8637076


Equipment
IMG-275777
A0000162
IMG-239664

IMG-341611

IMG-349390


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Conditions

2
 

When installing, the car must retain a temperature of 20 degrees C.

After installation, the car must not be washed for 48 hours

After installation, the car must not be driven for 2 hours

3
IMG-340635
 
4
IMG-344142
 

Clean the surface.

Use: 1161721, Isopropanol

5
IMG-344141
 

Matt the surface gently.

Use: , Sand paper P1000

6
IMG-344142
 

Clean the surface.

Use: 1161721, Isopropanol

7
IMG-344251
 

Caution!
Protect connector surfaces against paint spray.


Note!
Paint the sensors the same colour code as the vehicle.

Use: , Volvo Original Touch-up paint

Use base coat only.

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

8
IMG-333934
 

Caution!
First the paint must dry after painting.

9
IMG-332193
 

Set the ignition key to position 0.

10
IMG-292804
 

Remove the panel.

11
IMG-292806
 

Fold the carpet to the side.

12
IMG-292823
 
  1. Unhook the cable harness clips.

  2. Disconnect the connector.

13
IMG-292826
 

Remove the panel.

 

Vehicles with the 4C system.

14
IMG-292827
 

Disconnect the connector.

 

All vehicles

15
IMG-340983
 
16
IMG-340984
 

Disconnect the connector.

17
IMG-340985
 

Remove the screws.

18
IMG-340987
 

Remove the screws.

 

Cars with automatic transmissions

19
IMG-293006
 
20
IMG-293007
 

Release the shift-lock function.

 

All vehicles

21
IMG-340981
 
 

Cars with manual transmissions

22
IMG-345292
 
 

All vehicles

23
IMG-340636
 

Remove the screws.

24
IMG-340637
 
25
IMG-340638
 
26
IMG-340639
 
27
 

Reinstall the removed parts in reverse order.

28
IMG-340640
 

Remove the screws.

Repeat on the other side.

29
IMG-340642
 

Remove the screws.

30
IMG-340641
 

Repeat on the other side.

31
IMG-340643
 
 

Vehicles with keyless entry

32
IMG-340644
 

Disconnect the connector.

33
IMG-340645
 
34
IMG-340646
 
 

All vehicles

35
IMG-349422
 
36
IMG-349423
 
37
IMG-349316
 
38
IMG-349327
 

Use: Scribe

39
IMG-349328
 
40
IMG-349329
 


Use special tool: T9997234, Hole stamp

41
IMG-349330
 

Clean the surfaces.

Allow to dry.

Use: 1161721, Isopropanol

42
IMG-341991
 

Clean the surface.

Allow to dry.

Use: 1161721, Isopropanol

43
IMG-349331
 

Clean the surface.

Allow to dry.

Use: 1161721, Isopropanol

44
IMG-349334
 

Apply a thin and even layer.

Allow to dry for at least 10 minutes.

Use: 8637076, Activator

45
IMG-341992
 

Apply a thin and even layer.

Allow to dry for at least 10 minutes.

Use: 8637076, Activator

46
IMG-349335
 

Apply a thin and even layer.

Allow to dry for at least 10 minutes.

Use: 8637076, Activator

47
IMG-340657
 
48
IMG-340658
 
49
IMG-340660
 
50
IMG-340659
 
 

Vehicles with keyless entry

51
IMG-340661
 

Disconnect the connector.

52
IMG-340662
 

Remove the cable harness clips.

53
IMG-340663
 
54
IMG-340664
 
 

All vehicles

55
IMG-340666
 
56
IMG-340667
 
57
IMG-340668
 

Caution!
Make sure that the rubber grommet seals properly to the body.

58
IMG-340669
 
 

Vehicles without keyless entry

59
IMG-342946
 
60
IMG-342947
 

Tear off the excess foam tape.

 

Vehicles with keyless entry

61
IMG-340671
 
 

All vehicles

62
IMG-340672
 
63
IMG-340673
 
64
IMG-341997
 

Locate the pre-routed connector.

65
IMG-340676
 
66
IMG-340681
 
67
IMG-340682
 
68
IMG-340686
 
69
IMG-349351
 
70
IMG-340689
 

Note!
Prepare and install one holder at a time.

71
IMG-340690
 
72
IMG-349352
 

Note position of components.

73
IMG-340692
 
74
IMG-340694
 

Caution!
Make sure that equal pressure is applied to the full length of the component.


Note!
Ensure that the tape is fixed to the surface.

75
IMG-340695
 
76
IMG-340696
 

Put the wiring in the Bumper cover without installing the wiring.

77
IMG-340697
 

Connect the two painted sensors to the external connections.

78
IMG-340698
 
79
IMG-349397
 
80
IMG-349401
 
81
IMG-349403
 
82
IMG-340702
 
 

Vehicles without keyless entry

83
IMG-342948
 
84
IMG-342949
 

Tear off the excess foam tape.

 

Vehicles with keyless entry

85
IMG-340705
 

Connect the connector.

 

All vehicles

86
IMG-340706
 
87
 

Reinstall the removed parts in reverse order.

88
IMG-242268
 

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.