Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC60 2022
XC60 (18-) 2022

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
314548991.040005861, 40005839, 40005817, 40003558, 40003608, 40003578, 40003563, 40003603, 40003553, 40003543, 40003598
Fender extension (vehicles with variant code UF06)




 

Materials

Designation

Part number

Isopropanol

1161721

Primer

1161727


Equipment
IMG-268803
IMG-263203
IMG-425905
IMG-425896

IMG-421931

IMG-479248


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Further information

2
IMG-400007
 

Note!
If a pending accessories installation include the removing and replacing of the bumper, this installation should be carried out first.

When installing, the car must retain a temperature of 20 degrees C.

After installation, the car must not be washed for 48 hours

 

Color symbols

3
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

 

Applies to Battery Electric Vehicle (BEV)

4
IMG-479249
 

Note!
Paint the sensors the same colour code as the vehicle.

 

All vehicles

 

Removal

 

Vehicles with Parking assistance pilot

5
IMG-403425
 

Remove the marked part.

Use: Pliers

6
IMG-426018
 

Remove the screws.

Remove the marked part.

7
IMG-426020
 

Remove the screws.

Remove the marked part.

8
IMG-426045
 

Fold the wing liner aside.

9
IMG-426050
 

Release the catches.

Loosen the component indicated. Do not remove it.

10
IMG-426070
 

Remove the marked part.

Use: Interior trim remover

The part is not to be reused.

 

All vehicles

 

Accessory installation

11
IMG-426078
 

Note!
Make sure that the template is correctly located.

Hold the component in the position shown.

Make a hole, using the tool indicated.

Remove the Special Tool.

12
IMG-426095
 

Note!
Make sure that the template is correctly located.

Hold the component in the position shown.

Make a hole, using the tool indicated.

Remove the Special Tool.

13
IMG-426105
 

Clean the surfaces.

Allow to dry.

Use: 1161721, Isopropanol

14
IMG-426103
 

Remove the screw.

15
IMG-426104
 

Install component that comes with the accessory kit.

Reinstall the screw.

16
IMG-426136
 

Note!
Note the position.

Install component that comes with the accessory kit.

17
IMG-426137
 

Note!
This step is easier with two people.

  1. Hold the component in the position shown.

  2. Use: Masking tape

Remove the marked part.

18
IMG-426165
 

Note!
Note the position.

Install component that comes with the accessory kit.

19
IMG-426166
 

Note!
This step is easier with two people.

  1. Hold the component in the position shown.

  2. Use: Masking tape

Remove the marked part.

20
IMG-426170
 

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

21
IMG-426175
 

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

22
IMG-426191
 

Note!
Make sure that the template is correctly located.

Hold the component in the position shown.

Make a hole, using the tool indicated.

Remove the Special Tool.

23
IMG-426185
 

Clean the surfaces.

Allow to dry.

Use: 1161721, Isopropanol

24
IMG-426260
 

Note!
Note the position.

Install component that comes with the accessory kit.

25
IMG-426262
 

Note!
This step is easier with two people.

  1. Hold the component in the position shown.

  2. Use: Masking tape

Remove the marked part.

26
IMG-426263
 

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

27
IMG-426270
 

Note!
Note the position.

Install component that comes with the accessory kit.

28
IMG-426275
 

Note!
This step is easier with two people.

  1. Hold the component in the position shown.

  2. Use: Masking tape

Remove the marked part.

29
IMG-426276
 

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

30
IMG-426280
 

Note!
Note the position.

Install component that comes with the accessory kit.

31
IMG-426281
 

Note!
This step is easier with two people.

  1. Hold the component in the position shown.

  2. Use: Masking tape

Remove the marked part.

32
IMG-426282
 

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

33
IMG-426310
 

Fold the protective film forward

 

Vehicles with Parking assistance pilot

34
IMG-431030
 

Remove the marked part.

The part is not to be reused.

 

All vehicles

35
IMG-426136
 

Note!
Note the position.

Install component that comes with the accessory kit.

36
IMG-426311
 

Caution!
Pull carefully.


Note!
Press and apply pressure to the part over the tape for at least 20 seconds.


Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

37
IMG-426395
 

Install component that comes with the accessory kit.

Secure the template with tape.

Use: Masking tape

38
IMG-426332
 

Fold the protective film forward

39
IMG-426396
 

Note!
Note the position.

Install component that comes with the accessory kit.

40
IMG-426335
 

Caution!
Pull carefully.


Note!
This step requires the aid of another technician.


Note!
Adjust the position of the components to create even spaces.

Remove the protective film.

41
IMG-430895
 

Remove the screw.

Remove the marked part.

Reinstall the screw.

42
IMG-430881
 

Caution!
Pull carefully.


Note!
Press and apply pressure to the part over the tape for at least 20 seconds.


Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

 

Applies to Battery Electric Vehicle (BEV)

43
IMG-479124
 

Assemble components that come with the accessory kit.

44
IMG-479180
 

Disconnect the connector.

The part is not to be reused.

45
IMG-479176
 

Install component that comes with the accessory kit.

46
IMG-479177
 

Connect the connector.

 

All vehicles

47
IMG-426400
 

Fold the protective film forward

48
IMG-426260
 

Note!
Note the position.

Install component that comes with the accessory kit.

49
IMG-426401
 

Caution!
Pull carefully.


Note!
Press and apply pressure to the part over the tape for at least 20 seconds.


Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

50
IMG-426405
 

Install component that comes with the accessory kit.

Secure the template with tape.

Use: Masking tape

51
IMG-426410
 

Fold the protective film forward

52
IMG-426426
 

Note!
Note the position.

Install component that comes with the accessory kit.

53
IMG-426420
 

Caution!
Pull carefully.


Note!
Press and apply pressure to the part over the tape for at least 20 seconds.


Note!
Adjust the position of the components to create even spaces.

Remove the protective film.

54
IMG-426430
 

Fold the protective film forward

55
IMG-426436
 

Note!
Adjust the position of the components to create even spaces.


Note!
Note the position.

Install component that comes with the accessory kit.

56
IMG-426435
 

Caution!
Pull carefully.


Note!
Press and apply pressure to the part over the tape for at least 20 seconds.


Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

 

When necessary, carry out the following instruction.

57
IMG-420406
 

Remove the screws.

58
IMG-420407
 

Fold the wing liner aside.

59
IMG-431010
 

Note!
Adjust the position of the components to create even spaces.

Loosen the screws.

60
IMG-382211
 

Fold the wing liner aside.

61
IMG-412715
 

Note!
Do not loosen the bolts more than one turn.

62
IMG-431020
 

Note!
Adjust the position of the components to create even spaces.

 

Installation

63
 

Reinstall the removed parts in reverse order.

 

Accessory installation

64
 

Repeat the steps when installing accessories on opposite side.

65
IMG-242268
 

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.