Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Conditions

There may be parts in the accessories kit that are not needed for this installation.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Preparation

Removal

Remove the screws.

Detach the panel.

Disconnect the connector.

Remove the panel.

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Remove the screws.

Remove the panel.

Remove the panel.

Remove the marked part.

Detach the panel.

Remove the panel.

Remove the panel.

Remove the panel.

Remove the panel.

Remove the nut.

Remove the panel.

Remove the marked part.

Remove the marked part.

Remove the marked part.

Remove the marked part.

Vehicles with seven seats

Fold marked part aside.

All vehicles

Remove the screws.

Tightening torque: Cargo anchor, to body , 13 Nm

Remove the screw.

Vehicles with air suspension

Remove the marked part.

Disconnect the connector.

All vehicles

Remove the panel.

Disconnect any connector(s).

Depress the locking device.

Remove the marked part.

Depress the locking device.

Fold marked part aside.

Accessory installation

Remove the marked part.

The part is to be reused.

Remove the terminal. Use the wire only.

Use special tool: T9512620, Stripping tool (for wiring)

Use special tool: T9512785, Crimping tool (included in 9512669)

Use special tool: T9512777, Hot-air gun

All vehicles

Install component that comes with the accessory kit.

Route the cable harness to the existing cable harness.

Install the wiring harness.

Use a cable tie

Route the cable harness to the existing cable harness.

Install the wiring harness.

Use a cable tie

Fold marked part aside.

Route the cable harness to the existing cable harness.

Install the wiring harness.

Use a cable tie

Install component that comes with the accessory kit.

Install the cable.

Use tape

Position/route the cable harness as illustrated.

Fold the carpet aside.

Position/route the cable harness as illustrated.

Tighten the cable tie.

Tighten the cable ties.

Remove the nut.

Connect the prerouted cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Route the wire adjacent to existing wirings.

Tighten the cable ties.

Remove the marked part.

Depress the locking device.

Release the connector's catch.

Depress the locking device.

Remove the marked part.

Connect the cable harness terminals in the connector as follows.

Removal

Fold the carpet aside.

Fold marked part aside.

Remove the screws.

Remove the marked part.

Route the wire adjacent to existing wirings.

Tighten the cable ties.

Depress the locking device.

Release the connector's catch.

Release the catches.

Remove the marked part.

Connect the cable harness terminals in the connector as follows.

Preparation

Open the hood.

Removal

Remove the marked part.

Use: Electrician's screwdriver

Repeat on the other side.

Remove the nut.

Repeat on the other side.

Tightening torque: Windshield wiper arm , 28 Nm

Fold marked part aside.

Disconnect the connectors.

Loosen the clips.

On both sides.

Use special tool: T9997515, Puller

Fold marked part aside.

Repeat on the other side.

Remove the clips.

Remove the marked part.

Repeat on the other side.

Remove the marked part.

Loosen the clips.

Remove the screws.

Remove the marked part.

Remove the screws.

Remove the marked part.

Tightening torque: M6 , 10 Nm

Disconnect the connector.

Fold marked part aside.

Accessory installation

Remove the marked part.

Make a hole, using the tool indicated.

Pull the wiring through.

Use: Welding rod

Make a hole, using the tool indicated.

Pull the wiring through.

Use: Welding rod

Install component that comes with the accessory kit.

Position/route the cable as illustrated.

Tighten the cable ties.

Release the catch.

Fold marked part aside.

Remove the marked part.

Depress the locking device.

Remove the marked part.

Connect the cable harness terminals in the connector as follows.

Position/route the cable as illustrated.

Tighten the cable ties.

Release the catches.

Remove the marked part.

Remove the screws.

Fold marked part aside.

Position/route the cable harness as illustrated.

Remove the nut.

Tightening torque: M6 , 10 Nm

Release the locks.

Fold marked part aside.

Release the connector's catch.

Disconnect the connector.

Remove the screws.

Make a hole, using the tool indicated.

Pull the wiring through.

Use: Welding rod

Connect the cable harness terminals in the connector as follows.

Install component that comes with the accessory kit.

Reinstall the removed parts in reverse order.

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.