Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Further information

There may be parts in the accessories kit that are not needed for this installation.

Set the ignition key to position 0.

Removal

Remove the panel.

Disconnect the connector.

Release the catch.

Remove the panel.

Remove the screws.

Remove the screws.

Remove the panel.

1. Fold the carpet aside.

2. Unhook the clip(s).

3. Disconnect the connector.

Remove the panel.

Vehicles with the 4C system.

Disconnect the connector.

Cars with automatic transmissions

1. Release the shift-lock function.

2. Move the gear lever to D.

All vehicles

Detach the panel.

1. Release the catches.

2. Detach the panel.

Remove the panel.

Vehicles with the 4C system.

All vehicles

Disconnect the connector.

Remove the screws.

Accessory installation

Installation

Reinstall the screws.

Connect the connector.

Removal

Vehicles with Sensus Connect

Remove the screws.

Disconnect the connector, if applicable.

The connector is not to be used.

Attach the connector to the wiring harness.

Use: , Electrical tape

Disconnect the connectors.

Vehicles without Sensus Connect

Remove the screws.

Tightening torque: M8 , 24 Nm

Disconnect the connector.

Remove the screw.

Tightening torque: M8 , 24 Nm

Fold the carpet aside.

Remove the screw.

Tightening torque: M8 , 24 Nm

Fold the carpet aside.

Remove the screw.

Tightening torque: M8 , 24 Nm

Remove the screws.

Disconnect the connector, if applicable.

The connector is not to be used.

Attach the connector to the wiring harness.

Use: , Electrical tape

Disconnect the connectors.

All vehicles

Remove the panel.

Remove the weatherstrip.

Repeat on the other side.

Disconnect the connector, if applicable.

Repeat on the other side.

Remove the screw.

Remove the panel.

Remove the weatherstrip.

Detach the panel.

Detach the panel.

Remove the screw.

Remove the panel.

Detach the panel.

Repeat on the other side.

Release the catches.

Remove the panel.

Repeat on the other side.

1. Remove the screws.

2. Remove the panel.

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Remove the screws.

Tightening torque: M8 , 24 Nm

Detach the panel.

Remove the panel.

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Remove the screws.

Tightening torque: M8 , 24 Nm

Detach the panel.

Remove the panel.

Disconnect the connector, if applicable.

Remove the marked part.

Remove the clips.

Fold the insulation aside.

Remove the screw.

Repeat on the other side.

Detach the panel.

Repeat on the other side.

Detach the panel.

Repeat on the other side.

Remove the panel.

Remove the marked part.

Remove the screws.

Disconnect the connector.

Vehicles with power liftgate

Disconnect the connector.

All vehicles

Release the lock.

Remove the nuts.

Disconnect the connector.

Accessory installation

Use special tool: T9512932, Tension spring

Install the cable.

Use: , Electrical tape

Pull the wiring through.

Pull the wiring through.

Pull the wiring through.

Remove the Special Tool.

Connect the cable harness terminals in the connector as follows.

Depress the secondary lock.

Pull the wiring through.

Connect the connector.

Connect the connector.

Install the nuts

Tightening torque: Exterior handle to tailgate/luggage compartment lid , 5 Nm

Install the cable.

Use: , Strip clamp
Use: , Butyl tape

Install the cable.

Use: , Strip clamp
Use: , Butyl tape

Adjust the position of the wiring harness.

Install the cable.

Use a cable tie

Install the cable.

Use a cable tie

Position/route the cable harness as illustrated.

Position/route the cable harness as illustrated.

Disconnect the connector.

Connect the connectors.

Fold the insulation aside.

Position/route the cable harness as illustrated.

Position/route the cable harness as illustrated.

Fold the insulation aside.

Route the cable harness to the existing cable harness.

Fold the insulation aside.

Route the cable harness to the existing cable harness.

Position/route the cable harness as illustrated.

Position/route the cable harness as illustrated.

Vehicles without Sensus Connect

Position/route the cable harness as illustrated.

Connect the connectors.

Vehicles with 5 inch ICM-display

Connect the connector.

Vehicles with 7 inch display

Connect the connector.

Reinstall the removed part.

Vehicles with Sensus Connect

Connect the prerouted cable.

Reinstall the removed part.

All vehicles

Reinstall the removed parts in reverse order.

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.

Calibrate according to: DIAGNOSTICS/VEHICLE COMMUNICATION/Advanced/PAC/Service calibration, parking camera