Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Removal

Vehicles with Electric Engine Heater

Remove the clips.

Remove the screws.

Remove the marked part.

Remove the clips.

Remove the marked part.

Use: Pliers

Remove the marked part.

Remove the marked part.

Remove the screws.

Remove the marked part.

Fold marked part aside.

Alternative 1

Remove the cable tie(s).

Alternative 2

Remove the cable tie(s).

All vehicles

Release the lock.

Disconnect the connector.

Accessory installation

Lubricate the O-ring.

Install component that comes with the accessory kit.

Connect the connector.

Install the catch.

1. Cable from Engine block heater

2. Passenger Compartment Connector Cable

Install component that comes with the accessory kit.

Alternative 1

Install component that comes with the accessory kit.

Tighten the cable tie.

Alternative 2

Install component that comes with the accessory kit.

Tighten the cable tie.

Vehicles with gasoline engines

Position/route the cable harness as illustrated.

Tighten the cable ties.

Vehicles with diesel engines

Position/route the cable harness as illustrated.

Install the clip(s).

Tighten the cable tie.

Install the clip(s).

Install the clip(s).

Tighten the cable tie.

All vehicles

Position/route the cable harness as illustrated.

Tighten the cable ties.

Removal

Remove the clip.

Fold marked part aside.

Make a cut in the insulation.

Remove the nut.

Fold the insulation aside.

Remove the marked part.

The part is not to be reused.

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Fold the carpet aside.

Fold the insulation aside.

Accessory installation

Pull the wiring through.

Route the wiring harness into the passenger compartment.

Remove the marked part.

Insert the cable in to the passenger compartment, adjust the cable length out into the engine compartment and secure the rubber grommet.

Position/route the cable harness as illustrated.

Tighten the cable ties.

Installation

Refit the insulation.

Install the nut.

Reinstall the removed part.

Accessory installation

Place the component where indicated in the graphic.

Take the template from the kit and cut it out following the dotted line.

Measure and mark as illustrated.

Remove the marked part.

Remove the panel.

Fold the carpet aside.

Remove the screw.

The part is not to be reused.

Install component that comes with the accessory kit.

Tighten the screw.

Tightening torque: Cross member, to Body , 10 Nm

Install component that comes with the accessory kit.

Tighten the bolts.

Lubricate the O-ring.

Connect the connector.

Install the catch.

Fold the floor carpet back.

Install component that comes with the accessory kit.

Adjust and center the passenger compartment power outlet in the hole of the carpet. The purpose is to have the outlet bezel cover the carpet edge.

Installation

Reinstall the removed parts in reverse order.

Tightening torque: Aluminum wheel rim to wheel hub
Stage 1: 4 Nm
Stage 2: 50 Nm
Stage 3: 140 Nm