Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Preparation

Removal

Remove the screws.

Remove the screw.

Detach the panel.

Repeat on the other side.

Remove the part carefully

Remove the part carefully

Disconnect the connector, if applicable.

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Remove the part carefully

Disconnect the connector.

Remove the screw.

Remove the panel.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

Remove the panel.

Remove the panel.

Remove the screws.

Remove the panel.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

Accessory installation

Place the component where indicated in the graphic.

Scribe/mark up

Use tape

Loosen the wiring harness or move it to the side.

1. Install component that comes with the accessory kit.

2. Install the screws.

Repeat on the other side.

Repeat on the other side.

Tape the cables on the cable tie.

Use: , Electrical tape

Pull the wiring through.

Pull the wiring through.

Remove the cable tie(s).

Connect the cable harness terminals in the connector as follows.

Depress the secondary lock.

Connect the connector.

Clamp the cables and connectors to the existing cables to prevent noise.

Installation

Accessory installation

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Install the cable.

Connect the cable.

Vehicles with towbar

Connect the cable harness.

Clamp the cables and connectors to the existing cables to prevent noise.

Vehicles without tow hitch.

Connect the cable harness.

Clamp the cables and connectors to the existing cables to prevent noise.

All vehicles

Removal

Remove the rubber strip.

Remove the panel.

Vehicles with integrated child safety seat

Remove the screws.

All vehicles

Remove the marked part.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

Remove the panel.

Detach the panel.

Remove the panel.

When removing on right-hand drive cars, perform the procedures on the opposite side and/or mirrored.

Remove the screws.

Detach the panel.

Disconnect the connector.

Remove the panel.

Remove the panel.

Disconnect the connector, if applicable.

Remove the screws.

Remove the screws.

Note the position.

Disconnect the connector.

Unhook the cable harness clips.

Remove the marked part.

Remove the panel.

Remove the screws.

Remove the screws.

Cars with automatic transmissions

All vehicles

Detach the panel.

Remove the screws.

Accessory installation

Left hand drive vehicles

Position/route the cable harness as illustrated.

Route the wire adjacent to existing wirings.

Right-hand drive vehicles

Route the cable harness to the existing cable harness.

Clamp the cables and connectors to the existing cables to prevent noise.

All vehicles

Connect the prerouted cable.

Reinstall the removed part.

When installing on right-hand drive cars, perform the procedures on the opposite side and/or mirrored.

Fold the carpet aside.

Pull the wiring through.

Route the cable harness to the existing cable harness.

Clamp the cables and connectors to the existing cables to prevent noise.

Depress the locking device.

Release the connector's catch.

Disconnect the connector.

Release the catches.

Remove the marked part.

Release the connector's secondary lock.

Lift approximately 2 mm.

Connect the cable harness terminals in the connector as follows.

Reinstall the removed parts in reverse order.

Reinstall the removed part.

Connect the connector.

Reinstall the removed parts in reverse order.

Removal

Measure and mark as illustrated.

Use a drill with the stated size

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Accessory installation

Install component that comes with the accessory kit.

Installation

Reinstall the removed parts in reverse order.

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31428822