Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

After installation, the car must not be washed for 48 hours

When installing, the car must retain a temperature of 20 degrees C.

Paintwork

Use: , Masking tape

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

Use: 31335448, Bonding primer, plastic

Also see the instructions on the container.

Clean the surface.

Matt the surface gently.

Use: , Sand paper P1000

Clean the surface.

Allow to dry.

Use: , Volvo Original Touch-up paint

Use base coat only.

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

Use: , Volvo Original Touch-up paint

Use base coat only.

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

Remove the tape.

Removal

Set the ignition key to position 0.

Measure and mark as illustrated.

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Accessory installation

Removal

Remove the screw.

Remove the panel.

Remove the panel.

Detach the panel.

Release the catches.

Remove the panel.

Remove the screws.

Tightening torque: M8 , 24 Nm

Remove the screws.

Remove the panel.

Detach the panel.

Remove the panel.

Remove the screws.

Repeat on the other side.

Repeat on the other side.

Disconnect the connector.

Disconnect the connectors.

Unhook the cable harness clips.

The cable harness must not be reused.

Release the catches.

Accessory installation

Locate the markings for the positions.

Mark the centre.

Drill horizontally.

Use special tool: T9997234, Hole stamp

Use special tool: T9997483, Hole punch

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

Removal

Disconnect the connector.

Unhook the cable harness clips.

The cable harness must not be reused.

Accessory installation

Locate the existing connector in the vehicle's cable harness.

Connect the connector.

Install the cable.

Connect the connectors.

Remove the protective film.

Apply a thin and even layer.

Use special tool: T9512950, Glue gun (kit)

Use: 1161730, Mixing pipe

Use: 9511027, Glue

Remove the protective film.

Apply a thin and even layer.

Use special tool: T9512950, Glue gun (kit)

Use: 1161730, Mixing pipe

Use: 9511027, Glue

Reinstall the removed part.

Reinstall the removed part.

Install the cable.

Connect the connectors.

Place the Bumper Cover in position for installation.

Connect the connector.

Reinstall the bumper.

Reinstall the removed parts in reverse order.

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31266966