| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-400010 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components. Used for accessory components.
|
| | |
| | IMG-452753 |
|
| | Open the hood. Raise the car. |
| | IMG-452754 |
|
| | |
| | IMG-452756 |
|
| | Remove the marked detail/details. Use: Pliers 31423632
|
| | IMG-452752 |
|
| | Remove the screws. Remove the marked part. |
| | IMG-454295 |
|
| | |
| | IMG-452766 |
|
| | Remove the clips. Remove the nuts. |
| | IMG-452767 |
|
| | Remove the screws. Remove the clip. |
| | IMG-452769 |
|
| | |
| | IMG-452829 |
|
| | Remove the clips. Remove the screws. Remove the marked part. |
| | IMG-454296 |
|
| | |
| | IMG-452853 |
|
| | |
| | IMG-452889 |
|
| | Remove the screws. Loosen the component indicated. Do not remove it. |
| | Applies to the left-hand side: |
| | IMG-452964 |
|
| | Remove the connector from its attachment. Remove the cable harness clips. Remove the hose.
|
| | Applies to the right-hand side |
| | IMG-452966 |
|
| | Remove the cable harness clips. Remove the hose.
|
| | IMG-452938 |
|
| | |
| | IMG-400006 |
|
| | Drain the cooling system according to service information in VIDA: Information / Repair / Cleaning, Inspection and Adjustment / 2 Engine with mountings and equipment / 26 Cooling system / 261 radiator and connections / Cooling system – draining, charging and bleeding. Use special tool: T9997669, Key
|
| | |
| | IMG-453341 |
|
| | |
| | IMG-453346 |
|
| | |
| | IMG-453347 |
|
| | Saw in a way so that the marking remains. Use: Air-powered air saw
|
| | IMG-453354 |
|
| | Install component that comes with the accessory kit. Check that the flange of the part is in full contact with bumper cover. Adjust the hole with a file or knife as necessary. |
| | IMG-453355 |
|
| | Install component that comes with the accessory kit. |
| | IMG-453356 |
|
| | |
| | IMG-453357 |
|
| | Note! Do not fully tighten the nut yet. |
Install components that come with the accessory kit. |
| | IMG-453359 |
|
| | Install component that comes with the accessory kit. This is used as a counterhold. |
| | IMG-453358 |
|
| | Tighten the nut. Use hands only. |
| | IMG-453380 |
|
| | |
| | IMG-453385 |
|
| | Remove the nut. The item is to be reused. |
| | IMG-453393 |
|
| | Position/route the cable as illustrated. |
| | IMG-453389 |
|
| | Connect the prerouted cable. Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-453394 |
|
| | Position/route the cable as illustrated. Install the cables. Use a cable tie |
| | IMG-441390 |
|
| | Caution! No grease on contact surfaces. |
Lubricate the O-ring. |
| | IMG-453395 |
|
| | Install component that comes with the accessory kit. |
| | IMG-453400 |
|
| | |
| | IMG-453402 |
|
| | Use detail according to image. |
| | IMG-456435 |
|
| | Place the cable tie as illustrated. |
| | IMG-456436 |
|
| | Position/route the cable as illustrated. Tighten the cable tie. |
| | IMG-453691 |
|
| | |
| | IMG-453695 |
|
| | Position/route the cable as illustrated. |
| | IMG-453643 |
|
| | Place the cable tie as illustrated. Position/route the cable as illustrated. Tighten the cable tie. |
| | IMG-453697 |
|
| | Install a clips onto the upper edge of the subframe. Position/route the cable as illustrated. |
| | IMG-453699 |
|
| | Position/route the cable as illustrated. Install the cable. Use a cable tie |
| | IMG-465316 |
|
| | Steering gear Cable harness Engine heater cable
|
| | IMG-462742 |
|
| | Caution! The cable ties must not be assembled around the steering gear wiring harness. |
Note! Fasten the cable ties without tightening. |
Position/route the cable as illustrated. Install the cable. |
| | IMG-463899 |
|
| | Undo the hose from the connection. |
| | IMG-463902 |
|
| | Remove part of component according to image. |
| | IMG-463904 |
|
| | |
| | IMG-465222 |
|
| | Remove a piece of the protective cover. |
| | |
| | IMG-468911 |
|
| | |
| | |
| | IMG-465223 |
|
| | Remove the clip. Remove part of component according to image. |
| | IMG-463910 |
|
| | |
| | IMG-465196 |
|
| | Remove the protective film. |
| | IMG-463912 |
|
| | Install components that come with the accessory kit. Tighten the bolts. |
| | |
| | IMG-468915 |
|
| | Install the marked component. |
| | |
| | IMG-463919 |
|
| | Assemble components that come with the accessory kit. |
| | IMG-463920 |
|
| | |
| | IMG-463925 |
|
| | Attach the hose clamp Connect the hose. Tighten the hose clamp. |
| | IMG-463932 |
|
| | |
| | IMG-463937 |
|
| | Use: Scribe
Use: Pop rivet pliers
|
| | IMG-441390 |
|
| | Caution! No grease on contact surfaces. |
Lubricate the O-ring. |
| | IMG-463942 |
|
| | Connect the cable. Install the catch. |
| | IMG-465285 |
|
| | Fasten the cable tie without tightening. Adjust the cable position so that it can follow the motions of the engine. Tighten the cable tie. |
| | IMG-465329 |
|
| | |
| | |
| | IMG-377070 |
|
| | Reinstall the removed parts in reverse order. |
| | IMG-400006 |
|
| | Fill the cooling system according to the service information in VIDA: Information / Repair / Cleaning, Inspection and Adjustment / 2 Engine with mountings and equipment / 26 Cooling system / 261 radiator and connections / Cooling system – draining, charging and bleeding. Use special tool: T9997669, Key
Use special tool: T9512955, Cover
Use special tool: T9814192, Hose
Use special tool: T9512957, Coolant Reservoir
|
| | IMG-405228 |
|
| | Note! Make sure to follow the sequence indicated. |
Tightening torque: Aluminum wheel rim to wheel hub Stage 1:
4 Nm Stage 2:
50 Nm Stage 3:
140 Nm
|