Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC60 2009
XC60 (-17) 2009

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313165681.231414775, 31316358
Skid plate




 
Equipment
A0000162
IMG-297074
IMG-297076
IMG-246925
IMG-239981
IMG-247306
IMG-239664
A0000177
A0000214
M0000232
IMG-240693


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 
1A
IMG-297204
1B
IMG-297185
 

Illustrations A and B

  • Slacken off the screws.

2
IMG-297503
 

  • Carry out the procedure on the other side.

3A
IMG-297504
3B
IMG-297523
 

Illustrations A and B


Note!

This procedure is easier carried out by two people.


  • Place the bumper cover on a suitable surface.

4
IMG-285054
 

Applies to vehicles with parking assistance

  • Release the connector's catch.

  • Disconnect the connector(s).

  • Position the bumper so that it does not become damaged.

5A
IMG-338197
5B
IMG-338198
5C
IMG-338199
 

Applies to all models

Illustrations A, B and C

  • Carry out the procedure steps on the other side.

6A
IMG-338200
6B
IMG-338201
 

Applies to vehicles with parking assistance

Illustrations A and B

  • Carry out the procedure steps on the other side.

7A
IMG-338202
7B
IMG-338203
 

Illustrations A and B

  • Release the hooks.

8
IMG-337641
 

9
IMG-285095
 

Applies to vehicles with a towbar

  • Tape the skid plate on the outside opposite where it is to be sawed to prevent the saw foot from damaging the surface.

10
IMG-285512
 

Applies to vehicles with a detachable towbar

11
IMG-285513
 

Applies to vehicles with a detachable towbar

  • Saw out according to the markings. The shaded surface is to be removed.

  • Remove the tape.

  • Smooth off the sawn edges with a fine toothed file.


Note!

Do not damage the surface of the skid plate. Cut so that the raised edge on the inside remains. The raised edge marks the cut-out.


12
IMG-295363
 

Applies to vehicles with a fixed towbar

13
IMG-285096
 

Applies to vehicles with a fixed towbar

  • Saw out according to the markings. The shaded surface is to be removed.

  • Remove the tape.

  • Smooth off the sawn edges with a fine toothed file.


Note!

Do not damage the surface of the skid plate. Cut so that the raised edge on the inside remains. The raised edge marks the cut-out.


14
IMG-295746
 

Applies to vehicles with a towbar hitch

  • Measure and mark up for a cut-out for the tow hitch wiring.

15
IMG-295747
 

Applies to vehicles with a towbar hitch

  • Saw out according to the markings. The shaded surface is to be removed.

  • Remove the tape.

  • Smooth off the sawn edges with a fine toothed file.


Note!

Do not damage the surface of the skid plate. Cut so that the raised edge on the inside remains. The raised edge marks the cut-out.


16
IMG-337680
 

Applies to all models

17
IMG-337682
 

18
IMG-331352
 

Applies to vehicles with parking assistance

  • Locate the two markings at the lower edge of the bumper cover.

19
IMG-331358
 

  • Mark the centre, use a scriber.

20
IMG-331359
 

  • Extend the marking's vertical line using a scriber. This is to be used as a reference line for punching holes.

21A
IMG-331350
21B
IMG-331348
 

Illustrations A and B

  1. Ø 3 mm (7/64")

  2. Ø 10 mm (25/64")


Caution!

Drill horizontally through the bumper cover.


22
IMG-331360
 

  • Use: 9997367 Hole tool

  • Ensure that the markings, 1 and 2, are opposite each other when making holes.


Caution!

Place the hole tool's support sleeve on the inside, and the cutting part on the outside of the bumper casing.


23
IMG-331355
 

Applies to the left-hand side

  • Ensure that the marking on the hole tool (LH) and the marking that was made on the bumper cover are opposite each other.


Note!

Ensure that the support sleeve does not turn when the screw is tightened.


24
IMG-331356
 

Applies to the right-hand side

  • Ensure that the marking on the hole tool (LH) and the marking that was made on the bumper cover are opposite each other.


Note!

Ensure that the support sleeve does not turn when the screw is tightened.


25
IMG-338106
 

  • Clean using isopropanol.

26
IMG-338108
 

  • Clean using isopropanol.

27
IMG-339321
 

  • Apply a thin and even layer of activator. Allow to dry for at least 10 minutes.

  • Use: 8637076 Activator.

28
IMG-338111
 

  • Apply a thin and even layer of activator. Allow to dry for at least 10 minutes.

  • Use: 8637076 Activator.

29
IMG-338136
 

  • Apply two pieces of tape.

  • Use: 8637076 Activator.

30
IMG-338148
 

  • Apply a thin and even layer of adhesive. The adhesive must be above the tape level.

  • Use: 9512950 Adhesive gun, 1161730 Mixing pipe and 9511027 Adhesive.


Caution!

The adhesive must not come into contact with the tape.


31
IMG-297576
 

  • Repeat the method steps on the other cradle.

32
IMG-337687
 

33
IMG-297604
 

Applies to vehicles with parking assistance

  • Reinstall the detached components in reverse order

34
IMG-338196
 

Applies to vehicles without parking assistance

  • Reinstall the detached components in reverse order