Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

When installing, the car must retain a temperature of 20 degrees C.

After installation, the car must not be washed for 48 hours

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Applies to Battery Electric Vehicle (BEV)

All vehicles

Removal

Remove the marked part.

Use: Pliers

Remove the screws.

Remove the marked part.

Remove the screws.

Remove the marked part.

The part is to be reused.

Remove the clip.

Remove the screws.

The part is to be reused.

Remove the nuts.

Vehicles with air suspension

Loosen the clip.

All vehicles

Remove the marked part.

The part is not to be reused.

Loosen the clips.

Remove the marked part.

The part is not to be reused.

Remove any traces of glue.

Use: 1161721, Isopropanol

Vehicles with Parking assistance pilot

Release the catches.

Loosen the component indicated. Do not remove it.

Remove the marked part.

Use: Interior trim remover

The part is not to be reused.

All vehicles

Accessory installation

Install component that comes with the accessory kit.

Install the nuts

Reinstall the screws.

Install the clip(s).

Reinstall the removed part.

Reinstall the screws.

Hold the component in the position shown.

Make a hole, using the tool indicated.

Remove the Special Tool.

Hold the component in the position shown.

Make a hole, using the tool indicated.

Remove the Special Tool.

Clean the surfaces.

Allow to dry.

Use: 1161721, Isopropanol

Remove the screw.

Install component that comes with the accessory kit.

Reinstall the screw.

Install component that comes with the accessory kit.

1. Hold the component in the position shown.

2. Use: Masking tape
   

Remove the marked part.

Install component that comes with the accessory kit.

1. Hold the component in the position shown.

2. Use: Masking tape
   

Remove the marked part.

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

Removal

Remove the screws.

Remove the marked part.

The part is not to be reused.

Hold the component in the position shown.

Make a hole, using the tool indicated.

Remove the Special Tool.

Clean the surfaces.

Allow to dry.

Use: 1161721, Isopropanol

Install component that comes with the accessory kit.

1. Hold the component in the position shown.

2. Use: Masking tape
   

Remove the marked part.

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

Install component that comes with the accessory kit.

1. Hold the component in the position shown.

2. Use: Masking tape
   

Remove the marked part.

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

Install component that comes with the accessory kit.

1. Hold the component in the position shown.

2. Use: Masking tape
   

Remove the marked part.

Apply a thin layer of primer.

Allow to dry for at least 5 minutes but not more than 30 minutes.

Use: 1161727, Primer

Remove the tape.

Fold the protective film forward

Vehicles with Parking assistance pilot

Remove the marked part.

The part is not to be reused.

All vehicles

Install component that comes with the accessory kit.

Remove the protective film.

Install component that comes with the accessory kit.

Secure the template with tape.

Use: Masking tape

Fold the protective film forward

Install component that comes with the accessory kit.

Remove the protective film.

Remove the screw.

Remove the marked part.

Reinstall the screw.

Remove the protective film.

Applies to Battery Electric Vehicle (BEV)

Assemble components that come with the accessory kit.

Disconnect the connector.

The part is not to be reused.

Install component that comes with the accessory kit.

Connect the connector.

All vehicles

Fold the protective film forward

Install component that comes with the accessory kit.

Remove the protective film.

Install component that comes with the accessory kit.

Secure the template with tape.

Use: Masking tape

Fold the protective film forward

Install component that comes with the accessory kit.

Remove the protective film.

Fold the protective film forward

Install component that comes with the accessory kit.

Remove the protective film.

When necessary, perform the following instruction.

Remove the screws.

Fold the wing liner aside.

Loosen the screw.

Fold the wing liner aside.

Installation

Reinstall the removed parts in reverse order.

Accessory installation

Repeat the steps when installing accessories on opposite side.

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.