| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | After installation, the car must not be washed for 48 hours When installing, the car must retain a temperature of 20 degrees C. |
| | |
| | IMG-377265 |
|
| | |
| | IMG-377266 |
|
| | Clean the surface. Use: 1161721, Isopropanol
Allow to dry. |
| | IMG-377267 |
|
| | Use: 31335448, Bonding primer, plastic
Also see the instructions on the container. |
| | IMG-377194 |
|
| | |
| | IMG-352653 |
|
| | |
| | IMG-352654 |
|
| | Matt the surface gently. Use: , Sand paper P1000
|
| | IMG-352653 |
|
| | Clean the surface. Allow to dry. |
| | IMG-352655 |
|
| | Caution! Protect connector surfaces against paint spray. |
Note! Use correct color following the vehicle's paint code. |
Use: , Volvo Original Touch-up paint
Use base coat only. Use: 31335447, Varnish 2-component
Also see the instructions on the container. |
| | IMG-377267 |
|
| | Note! Use correct color following the vehicle's paint code. |
Use: , Volvo Original Touch-up paint
Use base coat only. Use: 31335447, Varnish 2-component
Also see the instructions on the container. |
| | IMG-352658 |
|
| | Caution! First the paint must dry after painting. |
|
| | IMG-377265 |
|
| | |
| | |
| | IMG-332193 |
|
| | Set the ignition key to position 0. |
| | IMG-377269 |
|
| | |
| | IMG-372212 |
|
| | Measure and mark as illustrated. |
| | IMG-372210 |
|
| | |
| | IMG-372209 |
|
| | Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304
|
| | IMG-372207 |
|
| | |
| | |
| | IMG-372208 |
|
| | |
| | |
| | IMG-377070 |
|
| | Note! The removal steps may contain installation details. |
|
| | IMG-377298 |
|
| | |
| | IMG-377299 |
|
| | |
| | IMG-377300 |
|
| | |
| | IMG-377302 |
|
| | |
| | IMG-377309 |
|
| | |
| | IMG-377320 |
|
| | |
| | IMG-343420 |
|
| | |
| | IMG-377345 |
|
| | |
| | IMG-377347 |
|
| | Release the catches. Remove the panel. |
| | IMG-307608 |
|
| | |
| | IMG-307609 |
|
| | |
| | IMG-377342 |
|
| | Remove the screws. Tightening torque: M8
, 24 Nm
|
| | IMG-346921 |
|
| | |
| | IMG-346811 |
|
| | |
| | IMG-346861 |
|
| | Remove the screws. Remove the panel. |
| | IMG-377350 |
|
| | |
| | IMG-377352 |
|
| | |
| | IMG-297185 |
|
| | |
| | IMG-377456 |
|
| | |
| | IMG-379308 |
|
| | Remove the screws. Repeat on the other side. |
| | IMG-379313 |
|
| | Repeat on the other side. |
| | IMG-379304 |
|
| | Disconnect the connector. |
| | IMG-379314 |
|
| | Caution! Place the Bumper Cover on a suitable surface. |
|
| | IMG-377368 |
|
| | Disconnect the connectors. Unhook the cable harness clips. The cable harness must not be reused. |
| | IMG-377371 |
|
| | |
| | IMG-377369 |
|
| | |
| | IMG-377372 |
|
| | |
| | |
| | IMG-377374 |
|
| | Locate the markings for the positions. |
| | IMG-377375 |
|
| | |
| | IMG-377377 |
|
| | |
| | IMG-331348 |
|
| | |
| | IMG-377378 |
|
| | Caution! Sharp end of tool must be on outside of cover. |
Use special tool: T9997234, Hole stamp
|
| | IMG-379343 |
|
| | Caution! Sharp end of tool must be on outside of cover. |
Note! Check that the markings are opposite each other and that they are pointing downwards when the tool is used. |
Use special tool: T9997483, Hole punch
|
| | IMG-377382 |
|
| | Clean the surfaces. Use: 1161721, Isopropanol
Allow to dry. |
| | IMG-377398 |
|
| | Clean the surfaces. Use: 1161721, Isopropanol
Allow to dry. |
| | IMG-377416 |
|
| | Clean the surfaces. Use: 1161721, Isopropanol
Allow to dry. |
| | IMG-377385 |
|
| | Apply a thin and even layer. Use: 8637076, Activator
Allow to dry for at least 10 minutes. |
| | IMG-377386 |
|
| | Apply a thin and even layer. Use: 8637076, Activator
Allow to dry for at least 10 minutes. |
| | IMG-377400 |
|
| | Apply a thin and even layer. Use: 8637076, Activator
Allow to dry for at least 10 minutes. |
| | IMG-377417 |
|
| | Apply a thin and even layer. Use: 8637076, Activator
Allow to dry for at least 10 minutes. |
| | |
| | IMG-308085 |
|
| | |
| | IMG-308086 |
|
| | |
| | IMG-297561 |
|
| | Disconnect the connector. Unhook the cable harness clips. |
| | IMG-297562 |
|
| | The cable harness must not be reused. |
| | |
| | IMG-377427 |
|
| | |
| | IMG-377426 |
|
| | |
| | IMG-377425 |
|
| | |
| | IMG-297565 |
|
| | Locate the existing connector in the vehicle's cable harness. Connect the connector. |
| | IMG-377428 |
|
| | Install the cable. Connect the connectors. |
| | IMG-377429 |
|
| | Note! Prepare and install one holder at a time. |
|
| | IMG-377401 |
|
| | Note! Ensure that the tape is fixed to the surface. |
Remove the protective film. |
| | IMG-377421 |
|
| | Warning! Wear protective gloves. |
Warning! Make sure to provide adequate ventilation. |
Apply a thin and even layer. Use special tool: T9512950, Glue gun (kit)
Use: 1161730, Mixing pipe
Use: 9511027, Glue
|
| | IMG-297571 |
|
| | |
| | IMG-297572 |
|
| | Note! Apply pressure only where the tape is located. |
Note! Ensure that the tape is fixed to the surface. |
|
| | IMG-297573 |
|
| | Note! Hold the part securely at the marker arrows when removing the tool. |
|
| | IMG-377418 |
|
| | Note! Prepare and install one holder at a time. |
Note! Ensure that the tape is fixed to the surface. |
Remove the protective film. |
| | IMG-377420 |
|
| | Warning! Wear protective gloves. |
Warning! Make sure to provide adequate ventilation. |
Apply a thin and even layer. Use special tool: T9512950, Glue gun (kit)
Use: 1161730, Mixing pipe
Use: 9511027, Glue
|
| | IMG-297576 |
|
| | Note! Apply pressure only where the tape is located. |
Note! Ensure that the tape is fixed to the surface. |
|
| | IMG-377430 |
|
| | Reinstall the removed part. |
| | IMG-377436 |
|
| | Reinstall the removed part. |
| | IMG-377431 |
|
| | Install the cable. Connect the connectors. |
| | IMG-373743 |
|
| | |
| | IMG-377435 |
|
| | |
| | IMG-379305 |
|
| | Place the Bumper Cover in position for installation. Connect the connector. |
| | IMG-379307 |
|
| | |
| | IMG-377070 |
|
| | Reinstall the removed parts in reverse order. |
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. Order and download software according to: 31266966
|