Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

There may be parts in the accessories kit that are not needed for this installation.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Removal

Remove the marked part.

Remove the panel.

Fold marked part aside.

Remove the screw.

Tightening torque: Seat belt guide, to Bracket , 4.4 Nm

Remove the panel.

Use hands only.

Release the catch.

Remove the marked part.

Remove the panel.

Use hands only.

Remove the clip.

Remove the panel.

Remove the screw.

Tightening torque: Cargo anchor, to body , 13 Nm

Remove the screw.

Tightening torque: Safety belt lower anchor to body (rear) , 40 Nm

Repeat the steps when removing on opposite side.

Remove the marked part.

Repeat on the other side.

Remove the screw.

Tightening torque: M6 , 10 Nm

Repeat on the other side.

Lift the marked component up

Release the lock.

Remove the marked part.

Remove the marked part.

Remove the marked part.

Vehicles with keyless entry

Release the catch.

Loosen the component indicated. Do not remove it.

All vehicles

Remove the screws.

Remove the marked part.

Remove the panel.

Disconnect any connector(s).

Remove the screws.

Remove the marked part.

Repeat the steps when removing on opposite side.

Replace Fixed side windows according to service information in VIDA:

Information/ Repair/ Removal, replacement, installation/ 8 Body and interior/ 84 Exterior trim, glass, weatherstrips/ 844 glass for side doors and window/ Fixed side window

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Remove the panel.

Disconnect the connector, if applicable.

Remove the screws.

Remove the panel.

Release the lock.

Repeat on the other side.

Remove the marked part.

Remove the panel.

Disconnect the connector, if applicable.

Remove the marked part.

Detach the panel.

Remove the panel.

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Disconnect the connector.

Remove the panel.

Disconnect the connector.

Remove the connector from its attachment.

Remove the screw.

Remove the screw.

Remove the panel.

Disconnect the connector.

Remove the screw.

Remove the screw.

Cars with automatic transmissions

Use special tool: T9512943, L-hook

Cars with manual transmissions

Use special tool: T9997077, Jimmy bar

Use special tool: T9997077, Jimmy bar

Release the locks.

Loosen the marked detail/details.

All vehicles

Remove the marked part.

Remove the screws.

Remove the cable tie(s).

Disconnect the connectors.

Remove the screws.

Remove the marked part.

Disconnect the connectors.

Remove the nut.

Accessory installation

Place the component where indicated in the graphic.

Install the nuts

Install the nut.

Tightening torque: M6 , 10 Nm

Adjust the component to a horizontal position.

Position/route the cable as illustrated.

Connect the connector.

Connect the connectors.

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Disconnect the connector.

Alternative 1

Connect the prerouted cables.

Alternative 2

Depress the secondary lock.

Connect the prerouted cables.

All vehicles

Use tape

Attach the connector to the wiring harness.

Use a cable tie

Route the wires adjacent to existing wirings.

Install the cables.

Use a cable tie

Route the wires adjacent to existing wirings.

Install the cable.

Use a cable tie

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

Remove the marked part.

Remove the nut.

Fold marked part aside.

Release the catches.

Fold marked part aside.

Remove the marked part.

Vehicles with Alcohol Analysing Start Inhibitor

Remove the marked part.

Use special tool: T9512631, Terminal removal tool (Color code: Brown)

Use special tool: T9512620, Stripping tool (for wiring)

Use special tool: T9512785, Crimping tool (included in 9512669)

Use special tool: T9512777, Hot-air gun

All vehicles

Connect the prerouted cable.

Reinstall the removed part.

Install the cable.

Use a cable tie

Reinstall the removed part.

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Connect the prerouted cables.

BK = Black

RD = Red

Depress the secondary lock.

Route the wires adjacent to existing wirings.

Install the cables.

Use a cable tie

Alternative 1

Remove the nut.

Connect the prerouted cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Alternative 2

Remove the nut.

Connect the cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Reinstall the removed part.

All vehicles

Connect the connector.

Position/route the cable as illustrated.

Use tape

Position/route the cable as illustrated.

Use tape

Position/route the cable as illustrated.

Use tape

Install component that comes with the accessory kit.

Install the screw.

Tightening torque: M6 , 10 Nm

Connect the prerouted cable.

Connect the connector.

Connect the connector.

Route the wire adjacent to existing wirings.

Use tape

Route the wire adjacent to existing wirings.

Install the cable.

Use tape

Route the wire adjacent to existing wirings.

Install the cable.

Use tape

Route the wire adjacent to existing wirings.

Install the cable.

Use tape

Position/route the cable as illustrated.

Install the cable.

Use tape

Install component that comes with the accessory kit.

Install the screw.

Tightening torque: M6 , 10 Nm

Connect the prerouted cable.

Connect the connector.

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

Position/route the cable as illustrated.

Position/route the cable as illustrated.

Fold the carpet aside.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Install the cable.

Use a cable tie

Position/route the cable as illustrated.

Connect the connector.

Tear off the excess foam tape.

Connect the connector.

Installation

Connect the connectors.

Reinstall the removed part.

Reinstall the screws.

Connect the connectors.

Install the wiring harness.

Use a cable tie

Accessory installation

Install component that comes with the accessory kit.

Scribe/mark up

Make a hole, using the tool indicated.

Install the nut.

Tighten the nut.

Use hands only.

Connect the prerouted cable.

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.

Installation

Reinstall the removed parts in reverse order.

Check for correct operation.

Place the manual for this accessory in a suitable location in the car.