electric engine heater, 230 V, R-design - XC60 2017 - Volvo Cars Accessories

2017 L.H.D

XC60 Cars

Installation Instruction

Installation instructions, accessories

Volvo Car Corporation Gothenburg, Sweden

XC60 2017

XC60 (-17) 2017 B4204T11, XC60 (-17) 2017 B4204T9, XC60 (-17) 2017 B4204T41

Instruction No		Version		Part. No.
31414354		1.0		31359329

electric engine heater, 230 V, R-design

IMG-378302

Materials
Designation	Part number
soap solution
Grease	1161761

Equipment

IMG-345497

IMG-239664

IMG-239660

IMG-239980

IMG-380133

IMG-380582

IMG-379391

Information

1

Read through all of the instructions before starting installation.
Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.
Ensure that all tools stated in the instructions are available before starting installation.
Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.
In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Conditions

2

When installing, the car must retain a temperature of 20 degrees C.

Color symbols

3

IMG-363036

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

Used for focused component, the component with which you will do something.
Used as extra colors when you need to show or differentiate additional parts.
Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.
Used when the component is not fully removed from the vehicle but only hung to the side.
Used for standard tools and special tools.
Used as background color for vehicle components.

Removal

4

IMG-332193

Set the ignition key to position 0.

5

IMG-351277

6

IMG-381134

Remove the screws.

Accessory installation

7

IMG-379415

Clean the Bumper Cover surface.

Use: , soap solution

8

IMG-379417

Note!
Check that the bar scale is correct.

Use the template in the installation instructions.

Cut following the dotted lines.

9

IMG-379439

Secure the template with tape.

10

IMG-379445

Caution!
Cut carefully to avoid unintentional damage or personal injury.

Adjust the hole with a file or knife as necessary.

11

IMG-381328

12

IMG-380613

13

IMG-363401

Removal

14

IMG-340576

Remove the screws.

Remove the panel.

15

IMG-341914

Fold the wing liner aside.

Accessory installation

16

IMG-380094

Caution!
Ensure that the wire or wiring harness cannot rub against adjacent components.

17

IMG-380095

18

IMG-381141

Note!
Orientation view

19

IMG-381142

20

IMG-362914

Caution!
No grease on contact surfaces.

Lubricate the O-ring.

Use: 1161761, Grease

Vehicles with passenger compartment connector

21

IMG-380096

Cable from front socket
Passenger Compartment Connector Cable
Cable from Engine block heater

22

IMG-380109

23

IMG-380111

Vehicles without passenger compartment connector

24

IMG-380654

Cable from front socket
Cable from Engine block heater

25

IMG-380662

All vehicles

26

IMG-381658

Attach any excess wire to the wiring harness.

27

IMG-380112

Removal

28

IMG-316303

Place a container under the car.

Drain the coolant.

29

IMG-380708

30

IMG-380929

Loosen the clip.

Accessory installation

31

IMG-380284

Installation

32

IMG-380928

Install the clip(s).

Removal

33

IMG-380706

Warning!
Be prepared to collect escaping fluid.

Loosen the clip.

Remove the hose.

34

IMG-380711

Remove the hose.

The part is not to be reused.

Accessory installation

35

IMG-380713

Install the hose.

Tighten the hose clamps.

36

IMG-381572

37

IMG-380720

Install the hose.

Tighten the hose clamp.

38

IMG-362914

Caution!
No grease on contact surfaces.

Lubricate the O-ring.

Use: 1161761, Grease

39

IMG-380723

Install the hose.

Tighten the hose clamp.

Connect the prerouted cable.

Install the catch.

Installation

40

IMG-363206

Reinstall the removed parts in reverse order.

Fill with coolant and run the engine to operating temperature.

Vent the cooling system and check for leakage.

Post-fill the cooling system if necessary.