Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
V60 2012
V60 (-18) 2012

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
307567241.030756714
Power socket in cargo compartment




 
Equipment
A0000162
IMG-239664
IMG-239660
IMG-282889
IMG-246925

IMG-343671


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 
1
IMG-332193
 

  • Set the ignition key to position 0.


Note!

Wait at least one minute before unplugging the connectors or removing other electrical equipment.


2
IMG-343672
 

3
IMG-343673
 

  • Remove the side cushion by first pulling it backwards at the upper edge until the hooks (1) release. Then pull it inwards slightly until the hook (2) releases, and upwards until the locating pin (3) disengages from the mounting at the rear edge.

4
IMG-343412
 

5
IMG-343413
 

6
IMG-343415
 

  • Repeat on both sides.

7
IMG-343676
 

8
IMG-343677
 

  • Remove the screw.

9
IMG-343678
 

10
IMG-343420
 

11
IMG-343679
 

12
IMG-343422
 

  • Remove the screws.

13
IMG-343423
 

14
IMG-343680
 

  • Remove the screws.

15
IMG-343681
 

16
IMG-343682
 

  • Use: 9995919 Hook. Insert into the holes on the upper edge of the cover. Turn the tool and pull off the cover.

  • Remove the loading eyelet screws. Tightening torque M8 screws: 24 Nm

17
IMG-343683
 

18
IMG-343684
 

  • Find the embossing on the reverse of the panel.

19
IMG-343685
 

  • Measure and mark the centre of the embossing using a scriber.

20
IMG-343686
 

21
IMG-343687
 

  • File out the hole with a square file and round file as illustrated.

  • Remove any swarf.

22
IMG-343688
 

23
IMG-343689
 

24
IMG-343691
 

25
IMG-343692
 

  • Remove the fuse.

26
IMG-343693
 

  • Install the fuse.

27
IMG-343694
 

28
IMG-343696
 

29
IMG-343697
 

  • Locate the connector.

30
IMG-343698
 

31
IMG-343699
 

  • Clamp the cables and connectors to the existing cables to prevent noise.

32
IMG-343700
 

Applies to vehicles with TRM

33
IMG-343701
 

  • Clamp the cables and connectors to the existing cables to prevent noise.

34
IMG-343702
 

Applies to all vehicles

  • Route the cable harness to the existing cable harness.

35
IMG-343703
 

36
IMG-343706
 

  • Remove the screw.

37
IMG-343710
 

  • Reinstall the screw. Tightening torque M6 screws: 10 Nm.

38
IMG-343711
 

Applies to vehicles without TRM

39
IMG-343713
 

  • Install the fuse in position F11.

40
IMG-343712
 

41
IMG-343714
 

Applies to all vehicles

42
IMG-343715
 

  • Reinstall the removed parts in reverse order.