Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
C30 2010

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313460861.431288762, 31350479, 31407108
Towbar, control module (TRM)




 
Equipment
IMG-242205
A0000162
IMG-239664
IMG-332314

IMG-359954


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

  

Note!

Some steps in these installation instructions are presented with illustration only.



Note!

When installing Velcro fasteners/tape the underlying surface must be kept at a temperature of at least +20° C (68°F).

There may be components in the accessories kit that are not used for this installation.


 

1
IMG-332193
 

  • Set the ignition key to position 0.


    Note!

    Wait at least one minute before unplugging the connectors or removing other electrical equipment.


2
IMG-240958
 

3
IMG-240957
 

4
IMG-241183
 

  • Remove the tailgate's sill panel by pulling it up until the four clips on the upper side and the eight catches at the lower edge release.

5
IMG-241184
 

  • Lift out the spare wheel, jack and other parts from the storage compartment in the cargo floor support.

6
IMG-241185
 

  • Pull off the seat cushion, first at the rear edge where it is secured by one holder. Then at the front edge where it is secured by two holders.

  • Remove the seat cushion.

7
IMG-246643
 

  • Fold the central arm rest forward.

  • Remove the central arm rest by grasping each end and pulling upwards until it releases at the rear edge from the backrest's lugs (1).

  • Then pull forwards until the holders (2) on the sides of the backrest have slid out of the corresponding cut-out (3) in the central arm rest.

8
IMG-250927
 

  • Fold the backrest forward.

  • Remove the panel for the backrest's right-hand mounting.

9
IMG-250928
 

10
IMG-250929
 

  • Fold the backrest away from the right-hand mounting.

  • Pull it out from the mounting at the arm rest and remove it.

11
IMG-250930
 

  • Pull off the rubber molding at the rear edge of the right-hand door opening.

12
IMG-251368
 

  • Remove the right-hand B pillar panel by prying it off at the sides at the lower edge using a weatherstrip tool. It is secured by three clips on the inside.

13
IMG-251370
 

  • Remove the screw from the right-hand panel in the rear seat.

  • Carefully pull the panel from the body side and unhook it from the sill panel at the front edge. It is secured by eleven clips on the inside.

14
IMG-253759
 

  • Remove the clips at the rear edge of the right-hand rear side panel.

  • Carefully pull the side panel off, starting at the front edge/upper edge and then straight back until all clips at the top edge have released.

  • Fold the panel inwards. Release it from the anchorage eyelets and lift it out of the load floor support.

15
IMG-261486
 

16
IMG-356179
 

  • Use: Isopropanol, 1161721. Wipe dry.

17
IMG-356181
 

18
IMG-222282
 

19
IMG-241925
 

20
IMG-356351
 

  • When installing Velcro fasteners/tape, the underlying surface must be kept at a temperature of at least +20° C (68°F).

21
IMG-261499
 

  • Find the grey 2-pin and green 5-pin connectors under the corner of the cargo compartment floor support. Lift up the cargo compartment floor support enough to improve accessibility.

22
IMG-261500
 

  • Use Isopropanol, 1161721. Wipe dry.


    Note!

    Do not position the lower edge of the control module below the dashed line, as the body plate is folded here.


23
IMG-356352
 

24
IMG-359492
 


Note!

When installing Velcro fasteners/tape the underlying surface must be kept at a temperature of at least +20° C (68°F).


25
IMG-359517
 

  • Plug in the connectors.

26
IMG-269603
 

Applies to cars from chassis number 39000-

  • Pull up the catch on the cover on the fuse box in the engine compartment. Pull up the cover and remove it.

27
IMG-269623
 

  • Install a 40A fuse in position 14.


    Note!

    The fuse included in the TRM kit must NOT be used.


  • Reinstall the cover.

28
 

  • Reinstall the detached components in reverse order.

29
IMG-242268
 

  • Download the software (application) for the accessory's function following the service information in VIDA.

    See VIDA or the accessories catalogue for software part number.