Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC60 2010
XC60 (-17) 2010

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
312141501.130784191
Running board




IMG-287283




 
Equipment
A0000162
IMG-287285
IMG-239664

IMG-287286

IMG-213320


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

  

Note!

Some steps in these installation instructions are presented with illustration only.


 

Preparations

1
IMG-245980
 

Preparations

  • Turn the ignition switch to position 0.


Note!

Wait at least three minutes before unplugging the connectors or removing other electrical equipment.


2
IMG-287287
 

3
IMG-285505
 

4A
IMG-296643
4B
IMG-296644
4C
IMG-296645
 

Removal of rear door

Illustration A

Illustration B

  • Carefully depress the catch on the connector in the door and pull off.

  • Remove the screws for the door stop.

Illustration C

  • Remove the screws in the upper and lower hinge.

5
IMG-296646
 

  • Lift off the door with a colleague.

  • Place the door out of harms way.

6
IMG-287303
 

Removal of the sill panel.

  • Pull off the sill panel at the rear edge, it is secured by six clips.

7
IMG-287304
 

  • Detach the rubber strip from the panel up to the front of the seven clips.

8
IMG-287306
 

  • Insert a small flat head screwdriver in the hole in the clip. Press so that the catches on the inside are pressed together and the upper edge of the panel can be prized off.

  • Carefully pry off the panel at the front and rear edge. It is secured by a clip at each end.

  • Remove the panel with the rubber strip.

  • Unhook the rubber strip from the panel.

9
IMG-296663
 

  • Remove all clips (8 pcs on each side) from the sill, and at the front and rear wing, and replace with new ones.

 
10
IMG-287323
 

  • Remove the front end of the panel. The end must be reused.

    The panel will not be reused.

11
IMG-287324
 

  • Take the front end of the panel and replace the old clips with new ones from the kit.

12
IMG-287343
 

  • Saw off 30 mm (1 3/16" ) from the upper baffle in the front sill panel.

  • File down the edges.

 

Installation

13
IMG-287344
 

Installation

  • Take the running board from the kit. Install the front end on the running board.

14
IMG-287345
 

  • Take the clips from the kit and press them onto the running board.

15
IMG-287346
 

  • Press the existing rubber strip onto the running board.

16
IMG-287347
 

  • Take four rivet nuts from the kit and tighten in the drilled holes in the sill. Use tool 9512782.


    Note!

    Rivet in the upper hole of the two adjacent holes for the rear mounting hole.


17
IMG-287348
 


Note!

Two people are needed for the following three steps.


  • Take the bracket from the kit and install on the sill. Tightening torque 50 Nm (37 lbf.ft.).

18
IMG-287349
 

  • Hang the running board on the attached bracket.

  • Align the locating pins in the front and rear end.

  • Align all clips in their holes on top and press securely. Ensure that all nine clips engage.

19
IMG-287351
 

  • Press the lower section of the running board with clips in the sill. Ensure that all six clips engage.

20A
IMG-296683
20B
IMG-296684
20C
IMG-296685
 

Illustration A

Illustration B

Illustration C

21
IMG-287352
 

22
IMG-287353
 

23
 

  • Repeat all steps for the other side.