Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

When installing, the car must retain a temperature of 20 degrees C.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Disconnecting the battery

Open the tailgate.

Open the hood.

Remove the battery's negative cable.

Removal

Remove the part carefully

Repeat on the other side.

Remove the marked part.

Remove the marked part.

Remove the marked part.

Remove the panel.

Fold marked part aside.

Remove the screw.

Tightening torque: Seat belt guide, to Bracket , 4.5 Nm

Remove the panel.

Remove the marked part.

Remove the marked part.

Remove the marked part.

Use: Interior trim remover

Remove the screws.

Tightening torque: Luggage compartment sill moulding to body , 4.5 Nm

Fold marked part aside.

Remove the marked part.

Disconnect the connector.

Accessory installation

Clean the surface.

Use: 1161721, Isopropanol

Wipe dry.

Clean the surface.

Use: 1161721, Isopropanol

Wipe dry.

Measure

Install component that comes with the accessory kit.

Remove the protective film.

Install component that comes with the accessory kit.

Removal

Make sure that the components are not mixed up at the installation.

Remove the marked part.

Remove the screws.

Remove the marked detail/details.

Remove the marked detail/details.

Remove the screws.

Remove the screws.

Remove the clip.

Remove the marked part.

Remove the marked part.

Use: Interior trim remover

Loosen the component indicated. Do not remove it.

Loosen the component indicated. Do not remove it.

Repeat the steps when removing on opposite side.

Locate the connector.

Release the connector's catch.

Disconnect the connector.

Request the aid of a colleague for this procedure.

Remove the marked part.

Remove the nuts.

The part is not to be reused.

Repeat on the other side.

Remove the marked part.

The part is not to be reused.

Remove the marked part.

The part is not to be reused.

Locate relevant marking.

Apply tape to the other side, opposite the marking lines.

Use: , Masking tape

Make a hole, using the tool indicated.

1. Mark using a pen

2. Remove the marked part.

Use: Air-powered air saw

Deburr edges

Accessory installation

Clean the surface.

Use: 1161721, Isopropanol

Clean the surface.

Use: 1161721, Isopropanol

Install component that comes with the accessory kit.

Install components that come with the accessory kit.

Tighten the bolts.

Tightening torque: Tow hitch member mounting to body frame (pre-tightening) , 30 Nm

Repeat on the other side.

Install component that comes with the accessory kit.

Install components that come with the accessory kit.

Tighten the nuts.

Tightening torque: Towbar, to Towbar member
Stage 1: 90 Nm
Stage 2: 60 Degree

Repeat on the other side.

Tighten the bolts.

Repeat on the other side.

Tightening torque: Tow hitch member mounting to body frame
Stage 1: 90 Nm
Stage 2: 60 Degree

Apply the stated Material on the marked surface.

Repeat on the other side.

Use: , Rust inhibitor

Route the wiring harness into the passenger compartment.

Fasten the wiring harness using the existing clips.

Fasten the wiring harness using the existing clips.

Remove the nut.

The part is to be reused.

Connect the prerouted cable.

Install the nut.

Tightening torque: Tow hitch ground connection, to body , 13 Nm

Locate the pre-routed connectors.

Connect the connectors.

Connect the prerouted cables.

Alternative 1

Remove the marked part.

Use: Interior trim remover

Install component that comes with the accessory kit.

Connect the prerouted cable.

Alternative 2

Remove the marked part.

Use: Interior trim remover

Install component that comes with the accessory kit.

Connect the prerouted cable.

Connect the connectors.

Installation

Reinstall the removed parts in reverse order.

Tightening torque: Aluminum wheel rim to wheel hub
Stage 1: 4 Nm
Stage 2: 50 Nm
Stage 3: 140 Nm

Connecting the battery

Reinstall the battery's negative cable.

Tightening torque: Battery cable for battery , 6 Nm

Accessory installation

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31664322

Check

Press the button.

Fold out the towbar.

If the components rub against each other, adjustments must be made to correct this.

1. Left indicator lamp

2. Fog tail lamps.

3. Ground connection

4. Right indicator lamp

5. Right position lamp

6. Brake light

7. Left position lamp

8. Back-up lamp

9. Battery voltage, constant

10. Battery voltage, ignition on

11. Ground connection

12. Not connected

13. Ground connection

Press the button.

Fold in the towbar.