Color symbols

1. Used for focused part, the part that you are to do something with.

2. Used as extra colors when you need to show or highlight additional parts.

3. Used for fasteners to be removed/installed. May be screws, clips, connectors, etc.

4. Used when part is not removed completely from the vehicle but is only hung/suspended off to the side.

5. Used for standard tools and special tools.

6. Used as background color on vehicle parts.

• Turn the ignition key to position 0.

  
  

  Note! Wait at least one minute before the connectors are unplugged, or other electric equipment is removed.

  
  

• Lift out the trunk mat.

• Remove the sill panel by first pulling it forward until the two clips at the leading edge release.

• Then pull up until the two clips at the top edge release.

• Fold forward the left backrest in the backseat.

Remove:

• the three clips at the top edge of the side panel.

• the four plastic nuts at the lower edge of the side panel.

• the connector for the trunk lighting.

• Lift out the side panel.

Installing TRM

• Use:Isopropanol, 1161721 Wipe off.

• Use:Isopropanol, 1161721 Wipe off.

When installing Velcro tape the surface must maintain a temperature of at least +20 ° C (68°F).

When installing Velcro tape the surface must maintain a temperature of at least +20 ° C (68°F).

• Press the control module securely into place.

Applies to cars equipped with rear parking camera.

• Disconnect the connectors.

• Remove the control module. It is fastened with Velcro straps.

• Remove the Velcro strap on the back of the control module.

• Remove the Velcro strap

• Remove the remains of glue

Use:Isopropanol, 1161721 Wipe off.

Use:Isopropanol, 1161721 Wipe off.

When installing Velcro tape the surface must maintain a temperature of at least +20 ° C (68°F).

When installing Velcro tape the surface must maintain a temperature of at least +20 ° C (68°F).

• Press the control module securely into place.

• Use: Isopropanol, 1161721 Wipe off.

When installing Velcro tape the surface must maintain a temperature of at least +20 ° C (68°F).

When installing Velcro tape the surface must maintain a temperature of at least +20 ° C (68°F).

• Press the control module securely into place.

• Plug in the connectors to the control module.

Applies to all models

• Locate the connectors in the car's cable harness.

• Plug in the connectors to the control module.

Installing trailer hitch cable harness

• Get four screws and nuts from the kit and install the socket (outlet) on the bracket.

• Remove the rubber bushing in the floor and put it aside, it is not to be used anymore.

• Insert the cable with the connector in the hole in the spare wheel well and install the rubber bushing.

• Adapt the length of the cable from the socket (outlet) and to the rubber bushing so that the cable is not too slack under the car.

• Get the ground screw from the kit and tighten down the ground cable in the grounding point in the rear harness. Torque-tighten the bolt, tightening torque: 10 Nm

• Plug in the green connector to the trailer module (TRM).

• Clamp the cable harness to the existing cable harness with two cable ties from the kit.

• Press in the catches on the black lid on the fuse holder and remove it.

• Install 40A fuse in position FA11.

Applies to all models

• Reinstall the removed parts in reverse order.

• Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.

Checking trailer socket

7-pin connection

1. Brake lights/Left turn signal

2. Ground

3. Spare (Brake lights, Electric brake)

4. Brake lights/Right turn signal

5. Charging

6. Running lights

7. Spare (Back-up light)

The cable for pin 3 for 7-pin connection is blue (BL). It is taped on the cable harness approx. 1 meter from the trailer socket.

4-pin connection

1. Brake lights/Right turn signal

2. Brake lights/Left turn signal

3. Running lights

4. Ground