Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

7. Used for accessory components.

Removal

Remove the marked part.

Remove the marked part.

Remove the screw.

Remove the marked part.

Detach the panel.

Remove the marked part.

Repeat on the other side.

Vehicles with heated rear seat

Disconnect the connector.

Repeat on the other side.

All vehicles

Remove the marked part.

Remove the marked part.

Remove the marked part.

Detach the panel.

Detach the panel.

Repeat on the other side.

Remove the marked part.

Remove the screws.

Remove the panel.

Remove the panel.

Remove the marked part.

Remove the screws.

Remove the marked part.

Detach the panel.

Disconnect the connector.

Remove the marked part.

Remove the marked part.

Remove the marked detail/details.

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Remove the marked detail/details.

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Remove the battery's negative cable.

Loosen the screws.

Disconnect the connector.

Disconnect the connector, if applicable.

Remove the screws.

Loosen the marked detail.

Vehicles with High Performance Sound

Disconnect the connector.

Vehicles with Premium Sound

Disconnect the connector.

Accessory installation

Loosen the tape temporarily.

The item is to be reused.

Use special tool: T9512620, Stripping tool (for wiring)

Use detail according to image.

Use special tool: T9512620, Stripping tool (for wiring)

Use special tool: T9512785, Crimping tool (included in 9512669)

Use special tool: T9512777, Hot-air gun

Connect the connectors.

Fold the carpet aside.

Route the cable harness to the existing cable harness.

Install the wiring harness.

Use a cable tie

Remove the screw.

Connect the ground cable.

Reinstall the screw.

Tightening torque: M6 , 10 Nm

Route the cable harness to the existing cable harness.

Install the wiring harness.

Use a cable tie

Fold the floor carpet back.

Place the overlap of the cable mat under the amplifier.

Reinstall the removed part.

Reinstall the screws.

Tightening torque: M6 , 10 Nm

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

Loosen the marked detail.

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

Assemble components that come with the accessory kit.

Install the marked component.

Install components that come with the accessory kit.

Connect the connectors.

Use details according to image.

Assemble components that come with the accessory kit.

Note the position.

Connect the connector.

Route the wire adjacent to existing wirings.

Install the cable.

Use tape

Use tape

Pull the wiring through.

Pull the wiring through.

Disconnect the connectors.

Remove the screw.

Remove the marked part.

The part is not to be reused.

Install component that comes with the accessory kit.

Install the screw.

Tightening torque: M6 , 10 Nm

Connect the connectors.

Assemble components that come with the accessory kit.

Depress the secondary lock.

Connect the connector.

Reinstall the removed parts in reverse order.

Reinstall the battery's negative cable.

Tightening torque: Battery cable for battery , 6 Nm

Order and download software according to VIDA/SOFTWARE.

Order and download software according to: 31382168

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31330938