Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
V60 Cross Country 2018
V60 Cross Country (-18) 2018

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
307564331.131295410, 31334457
Cruise control




 
Equipment
IMG-242205
A0000162

IMG-337681

IMG-344778


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Warning!

A pyrotechnic SRS component must not be unscrewed, repaired or transferred to another vehicle.

When temporarily storing the driver’s airbag (SRS) it must be positioned with the metal side (reverse side) down in a well protected site. This is to prevent damage to the surface material.


1
IMG-332180
 

  • Set the ignition key to position I to release the steering wheel lock.

  • Disconnect the battery negative lead.


Note!

The SRS system remains active for a brief period after power is disconnected. Thus, wait three minutes before starting work.


2
IMG-337651
 

  • Loosen the lever and pull the steering wheel console backwards.

  • Carefully prize off the rubber seal in the steering wheel cover all around.

3
IMG-329034
 

  • Carefully pull it off and remove the panel with the rubber seal.

4
IMG-328978
 

  • Carefully prize off the upper cover from the lower one at the rear. Remove the cover. It is fitted with clips at the sides.

5
IMG-344116
 

  • Turn the knob to access the hole on the reverse of the steering wheel.

6
IMG-337683
 

  • Use a 7 mm wide and 225 mm long screwdriver.

7
IMG-344725
 

  • Insert a screwdriver into the large hole on the rear of the steering wheel's rear face.

8
IMG-344726
 

  • Insert the tip of the screwdriver under the lock spring.

9
IMG-344727
 

  • Turn the screwdriver so that the end presses the lock spring up until it moves past the locking catch.

10
IMG-344117
 

  • Carefully pull off one side of the steering wheel module. It is firmly attached.

11
IMG-344118
 

  • Turn the steering wheel 180°.

  • Repeat for the lock spring on the other side.

  • Turn the steering wheel to neutral position.

12
IMG-329003
 

  • Carefully fold back the steering wheel module so that the connectors in the upper edge are accessible.

  • Press in the catches on the connectors (small illustration) and detach them.

  • Place the steering wheel module to one side with the front side facing upwards in a suitable location.

13
IMG-329005
 

  • Grip the panel in the upper left-hand corner and carefully pull it loose until the pin releases. Use both hands.

  • Repeat the operation on the other side.

14
IMG-339674
 

  • Use a weatherstrip tool, turn and carefully pull the panel loose at the bottom on both sides.

15
IMG-344119
 

  • Disconnect the cable to the keypad from its groove.

16
IMG-344120
 

  • Remove the right-hand keypad/keypad dummies by carefully prying them off using a weatherstrip tool.

  • Turn the weatherstrip tool to press out the keypad. It is firmly attached with three pins in the steering wheel, so force is required to remove them.

17
IMG-344121
 

  • Disconnect the cable and connector.

18
IMG-344122
 

19
IMG-344123
 

  • Place the cable in its groove.

20
IMG-339675
 

  • Reinstall the panel.

21
IMG-329019
 

  • Check that the three spring-loaded holders are firmly attached. If any holder has become trapped in the bottom of the steering wheel, remove it and fit it on the steering wheel module.

22
IMG-329020
 

  • Connect the two connectors to the steering wheel module.

  • Position the steering wheel module in the centre of the steering wheel and press it firmly into bottom of the steering wheel.

  • Check that it is fitted firmly and can be pressed in all around.

  • Reinstall the detached components in reverse order.

23
IMG-337646
 

  • Set the ignition key to position 0.

  • Reconnect the battery negative lead

24
IMG-336904
 


Warning!

When the ignition is to be switched on for the first time after the battery has been disconnected, this must be done whilst by standing outside the vehicle, stretching your arm in and avoiding the working area for the airbags.


  • Set the ignition switch to position II.

25
IMG-242268
 

  • Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.