| | IMG-214981 |
|
| | |
| | IMG-229604 |
|
| | |
| | IMG-221940 |
|
| | |
| | IMG-222060 |
|
| | |
| | IMG-222061 |
|
| | |
| | IMG-222062 |
|
| | |
| | IMG-222063 |
|
| | |
| | IMG-229620 |
|
| | |
| | IMG-229621 |
|
| | |
| | IMG-229622 |
|
| | |
| | J8903545 |
|
| | File out the small recesses using a small round file.
Note!
Do not file more than necessary, as there is otherwise a risk that the sensor holders will not cover the hole. |
File smooth the edges as required after making the recesses. Align the sensor holders in the filed out recesses on the outside of the bumper. The left-hand support is marked with the letter L, the two middle supports with the letter M, and the right-hand with the letter R. The hole may need adjusting with a file in order that the sensor holder connects firmly into the bumper cover. Remove the sensors from the bumper cover by clamping in the 3 catches and pressing out the sensor.
|
| | IMG-229623 |
|
| | Clean the sensors and holders with a wet cloth, P/N 9192678, and leave to dry. Apply a thin layer of activator, P/N 8637076, over the sensors and the holders.
Note!
Only paint the parts that are visible after installation. |
|
| | IMG-229624 |
|
| | |
| | IMG-221661 |
|
| | |
| | IMG-242961 |
|
| | |
| | IMG-242962 |
|
| | |
| | IMG-242963 |
|
| | |
| | IMG-226480 |
|
| | |
| | IMG-242964 |
|
| | |
| | IMG-226483 |
|
| | |
| | IMG-221942 |
|
| | |
| | IMG-221960 |
|
| | |
| | IMG-221961 |
|
| | Remove: the clip. the screw. the toolbox.
|
| | IMG-221962 |
|
| | |
| | IMG-242965 |
|
| | |
| | IMG-242966 |
|
| | |
| | IMG-242967 |
|
| | For cars with emergency release handle in cargo compartment Remove the emergency opening handle by pressing out the pin at the eye and unhook the wire.
|
| | IMG-221966 |
|
| | |
| | IMG-221967 |
|
| | |
| | IMG-221968 |
|
| | |
| | IMG-221969 |
|
| | |
| | IMG-221972 |
|
| | |
| | IMG-242968 |
|
| | Remove the load divider lock by using a weatherstrip tool to pry between the carpet and lock. If performing the operation on the left side, unplug the connector.
|
| | IMG-221974 |
|
| | |
| | IMG-242969 |
|
| | |
| | IMG-242970 |
|
| | Mark out the stop braces for the roof in relation to the screws and nuts on the right side. Remove the screw, nut and the roof's stop braces.
|
| | IMG-221976 |
|
| | |
| | IMG-221978 |
|
| | |
| | IMG-229640 |
|
| | Applies to cars with the Keyless system Remove the 2-pin grey connector for the Keyless system
|
| | IMG-229641 |
|
| | Applies to cars with the Keyless system Remove the Keyless system antenna by pushing it up. Remove the connector on the antenna by pulling out the red catch and pressing in the other catch.
|
| | IMG-229643 |
|
| | Applies to cars with the Keyless system. Remove the cable harness retaining clip. Remove the cable harness with rubber grommet.
|
| | IMG-229645 |
|
| | |
| | IMG-229646 |
|
| | Take the wiring that is included in the kit and which is used for the connection between the sensors and the Parking Assistance Module (PAS). Secure the wiring at the bumper member reinforcement using retaining clips, pull the connectors into the cargo compartment and install the rubber grommet.
|
| | IMG-229650 |
|
| | Applies to cars with the Keyless system. Plug the connector into the antenna. Press the catch back. Reinstall the antenna.
Applies to cars without the Keyless system. Secure the detached connector with a tie strap so that it is not damaged or does not rattle.
|
| | IMG-229651 |
|
| | |
| | IMG-229652 |
|
| | |
| | IMG-229654 |
|
| | Connect: the yellow 12-pin connector (1) to the control module's top connection. the black 16-pin connector (2) to the control module's bottom connection. the green 5-pin connector (3) to the green connector on the car's normal cable harness. the grey 2-pin connector (4) to the corresponding grey connector.
|
| | IMG-229655 |
|
| | Applies to cars with a tow hitch The existing green connector is plugged into the Trailer Module (TRM) towbar wiring (1). Unplug the connector from the control module and plug it into the cable harness female connector. Plug the green connector from the cable harness into the Trailer Module (TRM) towbar wiring.
Note!
It is important that the Parking Assistance Module (PAM) is connected as the first unit and that the cable harnesses are connected correctly, and not in a loop. |
|
| | IMG-229657 |
|
| | |
| | IMG-229658 |
|
| | |
| | IMG-229659 |
|
| | |
| | IMG-229660 |
|
| | Hint
It is easier to install the bumper if two persons help each other. |
|
| | Reinstall: the side panel. stops and attaching braces. the cargo compartment carpeting. the sill panel with lighting. emergency opener (if specified) - the stop for the boot lid. the stop for the boot lid/tailgate. the cargo lashing eyes, tightening torque: 24 Nm (17 lbf.ft.). the toolbox. the divider; remove the cable ties. the battery negative lead.
|