| | Preparations, apply to the S40 (04-) and V50 |
| | IMG-245980 |
|
| | Preparations, apply to the S40 (04-) and V50 |
| | J8601089 |
|
| | |
| | J8601058 |
|
| | |
| | J8504526 |
|
| | J8504527 |
|
| | Illustration A Illustration B |
| | Preparations, apply to the V50 |
| | J8504575 |
|
| | Preparations, apply to the V50 |
| | J8504577 |
|
| | Prize off the four external clips at the front edge/bottom edge of the sill trim panel on the tailgate. Pry up one of the corners of the sill trim panel so that the two clips at that end release. Use a weatherstrip tool. Pull up the sill trim panel so the remaining six clips release. Remove the panel. Detach the rubber strip where it covers the right-hand side panel in the boot opening.
|
| | J8504578 |
|
| | |
| | J8504702 |
|
| | Grasp the upper edge of the right-hand side cushion. Pull the side cushion forward so that the clip on the reverse releases (A). Slide the side cushion upwards. Remove the screw at the rear edge of the panel at the front/top of the right-hand side panel (B). Pull the panel upwards so that the four clips on the inside release.
|
| | J8504585 |
|
| | Pull off the rubber strip at the rear of the opening for the right-hand rear door. Carefully pry off the lower panel on the C-post on the right-hand side. Pry the top edge using a weatherstrip tool. Pull in the C-post panel so that the two upper clips release. Then continue pulling down until the last two clips release.
|
| | J8504570 |
|
| | Fold out the load securing eyelets on the right-hand side panel. Insert a scriber with an angled tip into the holes in the top of the covers (1). Turn the scriber so that the tip engages the reverse of the covers. Pull the covers off. Remove the screws in the load securing eyelets. Remove the screw (2) at the front/top edge of the side panel. Pull off the side panel at the top so that the two clips at the rear/bottom of the side window and the clip at the bottom of the D-post release. If the car has a 12V socket in the side panel, disconnect the connector from this socket. Lift out the side panel.
|
| | J3904767 |
|
| | Applies to cars with reversing warning systems Remove the back-up (reversing) warning system (PAS) from behind the right-hand wheel arch, to facilitate access to route the cable harness to the tow bar. If necessary, disconnect any surrounding wiring.
|
| | J8504615 |
|
| | |
| | Preparations, apply to the S40 (04-) |
| | J8504553 |
|
| | Preparations, apply to the S40 (04-) |
| | J8504552 |
|
| | |
| | J8504554 |
|
| | Unscrew the two external clips at the front edge/bottom edge of the sill trim panel on the tailgate. Pry up one of the corners of the sill trim panel using a weatherstrip tool so that the two clips at that end release. Pull up the sill trim panel at the other end so that the remaining two clips release. Remove the sill trim panel. Detach the rubber strip where it covers the right-hand side panel in the boot opening.
|
| | J8504691 |
|
| | Remove the three clips (1) that hold the right-hand side panel in the bodywork. Unhook the side panel from the mounting (2) on the underneath of the parcel shelf. Fold out the rear edge of the side panel from the bodywork. At the same time unhook the side panel from the rear load securing eyelet. If the car has a 12V socket in the side panel, disconnect the connector from this socket (if applicable). Fold out the side panel to access the space in the rear of the wheel arch.
|
| | J3904768 |
|
| | Applies to cars with reversing warning systems Remove the back-up (reversing) warning system (PAS) from behind the right-hand wheel arch, to facilitate access to route the cable harness to the tow bar. If necessary, disconnect any surrounding wiring.
|
| | Installing the trailer hitch connector, applies to the S40 (04-) and V50 |
| | J8903198 |
|
| | Installing the trailer hitch connector, applies to the S40 (04-) and V50 |
| | IMG-273184 |
|
| | IMG-273185 |
|
| | Illustration A applies to the S40 (04-) Illustration B applies to the V50 |
| | IMG-273333 |
|
| | Route the cable down underneath the collision member's right-hand mounting and secure it using the joined cable ties from the kit. Secure the cable at the collision member with two joined cable ties from the kit.
|
| | J8903624 |
|
| | |
| | IMG-272768 |
|
| | |
| | J8903538 |
|
| | J8903539 |
|
| | Illustration A applies to the V50 without RTI (road traffic information) Illustration B applies to the V50 with RTI (road traffic information) Remove the screws and the nuts holding the AM/FM tuner module (AFM) and the traffic message channel module (TMC) in the bodywork. Remove the AM/FM tuner module (AFM) and the traffic message channel module (TMC) from the bodywork. Disconnect the wiring if necessary. Place the AM/FM tuner module (AFM) and the traffic message channel module (TMC) to one side.
|
| | J8903623 |
|
| | |
| | J3703235 |
|
| | |
| | J3703240 |
|
| | Position | Cable | Function | 1 | 4 | Right indicator lamps | 2 | 10 | Charging | 3 | 15 | Left brake lamp | 6 | 8 | Reversing lamp | 7 | 16 | Right brake lamp | 8 | 2 | Fog lights | 10 | 1 | Left indicator lamps | 12 | 14 | Position lamps |
|
| | IMG-272771 |
|
| | IMG-272772 |
|
| | Illustration A applies to the S40 (04-) Illustration B applies to the V50 |
| | J8903629 |
|
| | J8903632 |
|
| | Illustration A Connect the white 2 pin male connector (1) in the pre-routed cable harness, to the existing white clamped 2 pin female connector (2) at the rear edge of the wheel housing. Take a cable tie from the kit and clamp the remaining white connector (3) on the pre-routed cable harness at existing cables at the rear edge of the wheel housing. Connect the ground lead (4) to the existing ground terminal under the right-hand tail lamp. Tighten the screw fully.
Image B applies to cars with a 12 V socket Connect the white 2 pin female connector (1) that was disconnected from the 12 V socket to the white 2 pin male connector (2) on the routed cable harness. Connect the remaining white 2 pin female connector (3) on the routed cable harness to the 12 V socket. Connect the ground lead (4) to the existing ground terminal under the right-hand tail lamp. Tighten the screw fully.
|
| | Applies to the S40 (04-)/V50 Refit the back-up (reversing) warning system (PAS), if the car is equipped with one. Refit any other detached cables. Reinstall the side panel.
Applies to the V50 Tighten the screws for the load securing eyelets. Tighten to 24 Nm (18 lbf.ft.). Reinstall the panel at the front/top of the side panel. Press downwards so that the catches engage. Tighten using the screw. Reinstall the C-post panel. Reinstall the rubber strip at the rear edge of the opening for the rear door. Reinstall the side bolster.
Applies to the S40 (04-)/V50 Reinstall the rubber strip in the tailgate opening. Reinstall the sill trim panel in the tailgate opening.
Applies to the S40 (04-)/V50 Reinstall the cargo compartment carpet.
Applies to the S40 (04-)/V50 Reinstall the bumper cover.
|
| | A3901793 |
|
| | Note!
For correct function, the trailer module (TRM) must be programmed with software before checks can be carried out. |
Checking the 13 pin connector. Position | Function | 1 | Left indicator lamps | 2 | Rear fog lamp | 3 | Ground | 4 | Right indicator lamps | 5 | Right rear position lamp | 6 | Brake lamp | 7 | Left rear running light | 8 | Reversing lamp | 9 | Power supply | 10 | Charging | 11 | Charging ground | 12 | Trailer indicator | 13 | Ground |
|