Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S80 2015
S80 (07-) 2015

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
314286251.131428882, 31428061
Parking assistance, camera, rear. For Sensus Connect




IMG-258000




 
Equipment
IMG-242205
IMG-345497
IMG-239664
A0000192
IMG-239660
IMG-239446
IMG-332313
IMG-333293
IMG-333288

IMG-353696


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

  

Note!

Some steps in these installation instructions are presented with illustration only.


 

Preparations

1
IMG-363036
 

Preparations


Note!

This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.


  1. Used for focused part, the part that you are to do something with.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

2
IMG-335491
 

  • Place the left front seat in its rearmost position.

  • Set the ignition key to position 0.

  • Disconnect the battery negative lead.


Note!

Wait at least one minute before unplugging the connectors or removing other electrical equipment.


3
IMG-254043
 

  • Remove the warning triangle from the trunk lid panel.

  • Remove the trunk lid's inner handle by first sliding it upwards and then bending it out at the lower edge using a weatherstrip tool.


    Note!

    The inner handle will no longer be used, there is a new handle in the kit.


4
IMG-254044
 

  • Pull out the central pin from the clips for the warning triangle's holder and remove them.

5
IMG-254045
 

  • Remove the clips from the trunk lid's panel and remove the panel.

6
IMG-249177
 

  • Fold together the cargo compartment carpet (1, 2) and remove it.

7
IMG-226721
 

  • Remove the rubber strips from the boot lid opening.

8
IMG-226722
 

  • Remove the trunk lid's sill trim panel. It is secured by two clips at the front edge (1) and two at the upper edge (2).

9
IMG-254103
 

  • Remove the seat cushion (1) by pulling up its front edge, pulling it forwards and then lifting it out.

  • Detach the two connectors for seat heating underneath the seat cushion.

10
IMG-257670
 

  • Fold the backrest forward.

  • Remove the seatbelt from the guide (1) on the side bolster.

  • Insert a hand from the side of the upper section of the side bolster. Press in the catches properly and jerk the upper edge of the bolster so that the two catches on the other side release. Lift the bolster from the mounting at the lower edge.

11
IMG-254105
 

  • Remove the three clips at the upper edge of the side panel and the four plastic nuts at the lower edge.

  • Remove the cargo compartment lighting connector.

  • Lift out the side panel.

  • Repeat for the other side.

12
IMG-254106
 

  • Measure a distance of 30 mm (1 3/16 ") from the rear edge of the rear fender and mark out a short line parallel to the rear edge. Use a piece of tape to make the markings on.

  • Measure 30 mm (1 3/16 ") from the rear edge of the gas cylinder's bracket to the previously drawn line. Mark out the middle of the hole that is to be drilled where the lines cross each other.

  • Pre-drill the hole using a Ø3 mm (1/8") bit.


    Note!

    Use a 5 mm (3/16 ") drill stop.


  • Drill out the hole to Ø8 mm (5/16 ") and then to Ø12 mm (15/32 ") to be able to insert the pull screw through for the hole making tool.


    Note!

    Do not damage surrounding painted surfaces.


  • Remove any swarf.

13
IMG-254107
 

  • Use holesaw bit, part.no 9997241 (Ø28.6 mm (1 1/8")), and enlarge the hole.

  • File down the edges of the holes.

  • Remove any swarf.

  • Apply primer part no. 9437350 around the hole edges and allow to dry.

14
IMG-254108
 

  • Measure for making holes for the rubber grommets in the trunk lid's front right-hand corner according to the diagram and mark out the middle.

  • Pre-drill the hole using a Ø3 mm (1/8") bit.


    Note!

    Use a 5 mm (3/16 ") drill stop.


  • Drill out the hole to Ø8 mm (5/16 ") and then to Ø12 mm (15/32 ") to be able to insert the pull screw through for the hole making tool.


    Note!

    Do not damage surrounding painted surfaces.


  • Remove any swarf.

15
IMG-254109
 

  • Use holesaw bit part no.9997241 (Ø28.6 mm (1 1/8")) and enlarge the hole.

  • File down the edges of the holes.

  • Remove any swarf.

  • Apply primer part no. 9437350 around the hole edges and allow to dry.

16
IMG-254110
 

  • Disconnect the connector for number plate lighting.

17
IMG-254111
 

  • Remove the trunk lid's trim strip by carefully prying it off from the trunk lid and number plate lighting's panel. It is securely fastened and will eventually break. New strip included in the kit.

  • Remove any tape residue from the trunk lid by heating the steel with a hot air gun. Do not heat above 80° C.

18
IMG-254112
 

  • Remove the four screws from the number plate lighting panel and remove it.

  • Remove the parts of the trim strip if it has broken.

19
IMG-346689
 

  • Remove the rubber strip.

20
IMG-338119
 

  • Remove the panel.

21
IMG-346676
 

22
IMG-346681
 

23
IMG-346677
 

24
IMG-346682
 

25
M8502823
 

  • Remove the sill panel in the door opening for the left-hand rear door by carefully pulling it upwards until the four clips release.

26
IMG-344717
 

  • Release the catch.

27
IMG-344721
 

28
IMG-344722
 

  • Remove the panel.

29
IMG-341879
 

  • Remove the screws.

30
IMG-341941
 

  • Unplug the connector.

 

Installing the parking camera

31
IMG-255733
 

Installing the parking camera

  • Drill/cut out a hole for the camera in the number plate lighting panel. Then remove the existing markings on the inside of the panel (see image).

  • Even off the edges carefully using a fine-toothed file.


    Note!

    Take care not to knock the surface that the camera is to be screwed to or to scratch it so that the seal becomes impaired.


32
IMG-255734
 

  • Drill out the holes in the protruding lugs using a Ø2.5 mm (3/32 ") drill bit.

  • Remove any swarf.

33
IMG-255735
 

  • Take two screws and the camera with the seal from the kit.

  • Screw the screws into the holes on the camera completely so that they rotate freely.

  • Insert the camera into the hole and screw it into place by tightening the screws crosswise so that the camera is tightened parallel to the panel.

34A
IMG-255736
34B
IMG-255737
 

Illustration A

  • Take the cable harness with the two rubber grommets from the kit. The rubber grommet (1) with the shorter cable end must go through the trunk lid.

  • Hook the cable holder onto the inner lower edge of the hinge section.

Illustration B

  • Place the cable holder so that the stop in the upper edge locates in the cut-out on the hinge.

  • Press the cable holder so that the upper section engages in the upper edge of the hinge.

35
IMG-255738
 

  • Insert the longer of the cables in the hole on the rear fender and press the rubber grommet securely into place. Ensure that the primer around the hole edges is not damaged.


    Note!

    Do not damage the rustproofing agent around the hole edges.


36
IMG-256323
 

  • Insert a wire into the right-hand hole on the trunk lid where the panel for the number plate lighting is, and pull it forwards in the hole on the trunk lid.

37
IMG-255739
 

  • Bind the connector to the shorter cable at the routed wire using tape.

  • Pull up the cable through the trunk lid and pull it out through the hole.

38
IMG-255740
 

  • Disconnect the cable from the wire.

39
IMG-255741
 

  • Press the rubber grommet into the trunk lid securely.


    Note!

    Do not damage the rustproofing agent around the hole edges.


  • Take the cable with the edge clip from the oval hole in the trunk lid and press the clip onto the hole edge.


    Note!

    Check that the cable is not over stretched between the trunk lid and the fender when the trunk lid is full open. Adjust the length of the cable in the rubber grommets.


40
IMG-255742
 

  • Pull the cable down from the rubber grommet in the rear fender and along the existing cable harness to the left-hand tail lamp.

  • Clamp the cable using tie straps from the kit as illustrated.

41
IMG-255743
 

  • Take the camera equipped panel for the number plate lighting.

  • Connect the connector to the routed cable harness for the reversing camera.

  • Guide the cable for the number plate lighting through the hole in the trunk lid.

  • Reinstall the panel and tighten. Ensure that the cables for the number plate lighting are not trapped.

42
IMG-255744
 

  • Use isopropanol and clean the marked surface on the boot lid where the chrome strip tape will sit. Wipe dry.

43
IMG-255745
 

  • Take the new trim strip from the kit. Remove the protective film from the adhesive tape.

44
IMG-255746
 


Note!

During installation the underlying surface must be kept at a temperature of at least +15 °C (59 °F).


  • Insert the trim strip clips in the corresponding holes on the panel. Ensure that the strip's locating pins align with the holes on the trunk lid.

  • Press the strip firmly along the entire length of the trunk lid and the panel so that the tape adheres.

45
IMG-255747
 

  • Connect the number plate lighting connector on the inside of the trunk lid.

46
IMG-255748
 

  • Reinstall the panel on the inside of the trunk lid.

47
IMG-255749
 

  • Reinstall the warning triangle's holder and press the middle pins of the clips in.

48
IMG-255750
 

  • Take the new inner handle from the kit and press it onto the boot lid.

  • Refit the warning triangle holder and the warning triangle on the boot lid.

 

Installing the Parking Assistance Camera (PAC)

49
IMG-255751
 

Installing the Parking Assistance Camera (PAC)

  • Take the control module from the kit.

  • Clean the two polished surfaces on the control module using isopropanol.

  • Wipe dry.

50
IMG-222282
 

  • Take two Velcro strips from the kit and cut them in the middle to create four equal parts.

51
IMG-222283
 

  • Press the Velcro strips two and two.

52
IMG-222285
 

  • Remove the protective film from one side of the two attached Velcro strips.

53
IMG-255752
 

  • Press the Velcro strips onto the cleaned surfaces of the control module.

54
IMG-255754
 

  • Clean the surfaces under the tail lights with isopropanol. Wipe dry.

55A
IMG-273804
55B
IMG-273823
55C
IMG-273824
 


Note!

The adapter cable A was included in a previous version of the kit for the parking camera.

The adapter cable B was included in a later version of the kit for the parking camera.

Both versions are suitable for all cars.


Illustration A

  • Connect the previously routed cable harness connector (1) to the right-hand connector on the control module.

  • Take the adapter cable A/B from the kit and connect the large green connector to the socket on the control module, as illustrated.

  • Connect the connector (2) on the pre-routed, taped cable harness for the power supply under the left-hand tail lamp, to the corresponding connector on the adapter cable.

  • Take the long remaining cable harness from the kit and connect the end with the gray connector (3) to the connector in the middle of the control module.

  • Clamp the adapter cable's remaining connector using the tie strap from the kit.

Figure B shows adapter cable A

Figure C shows adapter cable B

56
IMG-255753
 

  • Remove the protective film from the installed Velcro strips.

57
IMG-273825
 

  • Press the control module upwards firmly as high as possible on the flat surface under the tail lamp, according to the measurements illustrated.

58
IMG-255757
 

Applies to cars with a TRM module.

  • Remove the two connectors from the top of the TRM module.

  • Remove the TRM module from the Velcro strips on the plate under the rear lamp and place to one side.

59
IMG-255758
 

  • Allow the old Velcro strips to remain in the body.

60
IMG-222285
 

  • Remove the protective film from the Velcro strips.

61
IMG-255759
 

  • Press the Velcro strips on to the cleaned surfaces on the Parking Assistance Camera (PAC).

62A
IMG-273826
62B
IMG-273863
 


Note!

The adapter cable A was included in a previous version of the kit for the parking camera.

The adapter cable B was included in a later version of the kit for the parking camera.

Both versions are suitable for all cars.


Figure A shows adapter cable A

Figure B shows adapter cable B

  • Connect the previously routed cable harness connector to the right-hand connector on the control module (1).

  • Take the adapter cable A/B from the kit and connect the large green connector to the socket on the control module, as illustrated.

  • Connect the connector (2) on the pre-routed cable harness for the power supply to the corresponding contact on the adapter cable.

  • Take the long remaining cable harness from the kit and connect the end with the gray connector (3) to the connector in the middle of the control module.

63
IMG-273864
 

  • Press the control module firmly onto the existing Velcro straps under the tail lamp.

64
IMG-273865
 

  • Clean the marked surfaces on the control module with isopropanol. Wipe dry.

65
IMG-255763
 

  • Remove the marked Velcro strip from the TRM module.

66
IMG-222282
 

  • Take two Velcro strips from the kit and cut them in the middle to create four equal parts.

67
IMG-255764
 

  • Clean the marked surfaces on the TRM module with isopropanol. Wipe dry.

68
IMG-222285
 

  • Remove the protective film from one of the Velcro strips.

69
IMG-255765
 

  • Press the Velcro strip on to the TRM module beside the other strip, as illustrated.

70
IMG-255766
 

  • Press the two Velcro strips onto the TRM module's two existing Velcro strips.

71
IMG-255767
 

  • Remove the protective film from the Velcro strips.

72
IMG-273866
 

  • Press the TRM module onto the control module securely, as illustrated.

73
IMG-273867
 

  • Connect the remaining green connector (1) on the adapter cable for the power supply to the corresponding socket in the TRM module.

  • Connect the remaining gray connector (2), which was removed from the TRM module.

74
IMG-273869
 

Steps 70-71 only apply to cars with adapter cable B for the power supply

  • Route the long ground lead in the adapter cable to the right-hand side of the rear harness.

  • Connect the cable to the lower of the ground screws and tighten the screw with 10 Nm (7.5 lbf.ft.)

75
IMG-273870
 

  • Wash the rear crossmember using isopropanol where the ground lead is to be taped. Wipe dry.

  • Secure the cable using a wide piece of silver/fabric tape or similar.


    Note!

    The ground lead must only be taped at the rear crossmember, it must not be secured by the thick cable harness.


76
IMG-257676
 

  • Route the previously connected cable harness inside the insulation panel at the left-hand rear wheel arch and out through the hole in the body.

  • Take a tie strap from the kit and secure the cable at the fuse holder's cable harness.

77
IMG-354975
 

  • Remove the foam tape from the kit and split it in the centre.

78
IMG-241925
 

  • Remove the protective film from the foam tape.

79
IMG-353731
 

  • Apply the foam tape around the wiring to protect the cable from sharp edges.

80
IMG-255771
 

  • Pull out the B post panel at the lower edge until the two clips release.

  • Continue to route the cable harness inside the B post panel and forwards in the car. Route the cable harness along the left-hand side, in front of the floor and insulation panels, up to the front edge of the door opening.

81
IMG-384934
 

Only applies to left-hand drive vehicles

  • Route the cable harness inside the floor and insulation panels, up on the A pillar slightly, and then at an angle upwards, between the A pillar and the end panel, towards the dashboard. Route the cable harness to the location indicated.

  • Place the cable harness so that it does not come into contact with sharp edges or moving parts under the dashboard.

82
IMG-384940
 

Only applies to right-hand drive vehicles

  • Take a piece of wire and insert it by the air ducts through the hole for the DVD unit. Pull it out to the left, above the glove compartment and out through the left-hand end of the dashboard.

  • Tape the connector on the cable by the wire.

  • Route the cable to the location indicated.

83
IMG-353636
 

Applies to all vehicles

  • Take a tie strap from the kit and secure the cable in the hole on the end as illustrated.

 

Removal

84
IMG-349804
 

Removal

  • Remove the panel.

85
IMG-349806
 

  • Remove the screws.

86
IMG-345282
 

  • Remove the screws.

87
IMG-345747
 

Cars with manual transmissions

  • Release the lock, which is located inside the gear shift gaiter

88
IMG-347222
 

89
IMG-345283
 

Cars with automatic transmissions

90
IMG-345284
 

  • Release the shift-lock function.

  • Place the gear lever in position D.

91
IMG-341878
 

  • Remove the panel.

92
IMG-346036
 

  • Remove the panel.

93
IMG-340599
 

Detach the following components:

  1. Fold back the mat

  2. Unhook the clip

  3. Unplug the connector

94
IMG-353601
 

95
IMG-353602
 

  • Remove the screws.

96
IMG-347139
 

  • Remove the panel.

97
IMG-345317
 

Vehicles with the 4C system

98
IMG-349826
 

All vehicles


Caution!

Do not damage the hooks.


  • Remove the panel.

99
IMG-340605
 

  • Remove the screws.

Remove the screws.

100
IMG-345296
 

101
IMG-380815
 

 

Accessory installation

102
IMG-380816
 

Accessory installation

 

Removal

103
IMG-349942
 

Removal

104
IMG-349946
 

 

Accessory installation

105
IMG-384929
 

Accessory installation

  • Connect the routed cable to the DVD unit as illustrated.

 

Installation

106
IMG-349948
 

Installation

107
 

  • Reinstall the detached components in reverse order

 
108
IMG-336901
 

  • Reconnect the battery negative lead

109
IMG-336904
 


Caution!

When the ignition is to be switched on for the first time after the battery has been disconnected, this must be done whilst by standing outside the vehicle, stretching your arm in and avoiding the working area for the airbags.


  • Set the ignition switch to position II.

110
IMG-242268
 

  • Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.

 

Check

111
IMG-354602
 

Check

Perform a function test as follows:

  • Engage reverse gear.

  • The display is activated.

  • Wait for the message "Update Environment" to appear on the screen.

  • Follow the on-screen instructions.

  • Switch off the ignition for at least 10 seconds.

  • Turn the ignition on.

  • The display is activated.

  • Check that the support lines appear on the screen and that these react to steering wheel movements.