• Clean the sensors. Use: Isopropanol.

• Allow to dry.

• Carefully mat down the surface. Use Glasspaper, grade P1000.

• Clean the sensors again.

• Use: Isopropanol

• Allow to dry.

• Avoid contact with the cleaned surfaces.

• Paint the sensors in the same colour code as the vehicle.

• Use Volvo Touch-up paint (only use base coat).

• Use: Volvo 2-K Varnish, P/N: 31335447

• Set the ignition key to position 0.

• Remove the panel.

• Remove the screws.

• Remove the screws.

Applies to vehicles with manual transmissions

Applies to vehicles with automatic transmissions

• Release the shift-lock function

Applies to all vehicles

• Remove the panel.

1. Fold back the mat.

2. Unhook the cable harness clips.

3. Unplug the connector.

• Remove the covers.

• Remove the screws.

Applies to vehicles with the 4-C system

• Remove the panel.

• Unplug the connector.

Applies to all models

• Remove the panel.

• Remove the cover plug.

• Install the switch.

• Reinstall the detached components in reverse order.

• Remove the four screws holding the end of the rear bumper.

• Repeat the operation on the other side.

• Remove the two nuts at the lower edge of the bumper cover.

• Pull the corner straight out, continue to pull the bumper cover backwards until the five clips at the upper edge release.

• Repeat the operation on the other side.

• Open the boot lid/tailgate.

• Remove the bumper cover by pulling it backwards until the three catches opposite the tailgate opening have released.

• Locate the 4 markings on the inside of the bumper cover.

• Mark the centre, use a scriber.

• Drill out the markings using a Ø 3 mm (1/8") diameter drill bit.

• Drill out the holes. Use a Ø 10 mm (13/32") diameter drill bit.

• Enlarge the holes in the bumper cover.

Use special tool: 9997234 Hole tool

• Clean around the holes and markings.

• Use: Isopropanol.

• Allow to dry.

• Take four holders from the kit.

• Clean the holders on the surface as illustrated. Use: Isopropanol.

• Allow to dry.

• Apply a thin and even layer of activator to the cleaned surfaces where the tape is to be attached. Let dry for at least 1 minute. Use: 8637076 Activator.

• Apply a thin and even layer of activator to the cleaned surfaces where the tape is to be attached. Let dry for at least 10 minutes. Use: 8637076 Activator.

• Lift out the cargo compartment carpet.

• Remove the sill trim panel by first pulling it forward until the clips in the front edge release. Then pull it upward until the clips in the top edge release.

• Fold forward the right backrest in the backseat.

Remove:

• the clips

• the plastic nuts

• Connector to the cargo compartment lighting

• Side panel

Unplug connector for 12V outlet, if installed.

• Locate the two studs positioned on the right-hand side underneath the tail lamp in the cargo compartment. Press the control module's holder on the studs.

• Press the control module on the holder.

• Remove the rubber seal.

• Remove the support under the left-hand tail lamp by removing the two screws.

• Take the short cable harness and thread the end with the black connector through the hole in the body.

• Install the rubber seal.

• Reinstall the support under the left-hand tail lamp.

• Hook the connector onto the rail.

• Connect the newly routed cable harness to the control module.

• Locate the light brown connector. It originates from the same cable harness as the connector for cargo compartment lighting.

• Connect the connector to the control module.

Reinstall:

• the side panels

• the sill trim panel

• the floor carpet

• Fold up the backrest.

Installing sensors

Installing sensors

• Check which holder is to be positioned where before installing. The two middle holders are the same whilst the two outer holders are specific.

• Apply two pieces of tape to each holder.

• Remove the protective film from the tape.

• Apply a thin layer and even layer of adhesive.

Use special tool: 9512950 Adhesive gun.

Use: 1161730 Mixing pipe.

Use: 9511027 Adhesive.

• Install the centering tool in one holder.

• Install the holder on the bumper cover.

• Hold the holder securely when removing the centering tool. The holder must be installed horizontally and in line with the bumper cover.

• Repeat the steps until all four holders are in place.

• Connect the cable harness connectors to the sensors.

• Install the sensors in their holders. Take care when installing so that the holder does not release from the tape.

• Press the six cable holders on the longitudinal flange in the bumper casing.

Installing the bumper

Installing the bumper

• Lift up the bumper and connect the connector

• Press all of the bumper's hooks in at the rear edge. Press all the hooks for the ends into the body.

• Reinstall the screws on the front edges of the bumper casing.

• Reinstall the plastic nuts at the lower edge.

• Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.