Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Removal

Set the ignition key to position 0.

Remove the panel.

Remove the weatherstrip.

Fold the carpet to the side.

Locate the rubber grommet under the insulating mat.

Fold the insulation to one side.

Remove the marked part.

The part is not to be reused.

Repeat on the other side.

Disconnect the connector, if applicable.

Repeat on the other side.

Remove the panel.

Remove the weatherstrips.

Detach the panel.

Remove the screws.

Remove the panel.

Remove the panel.

Turn the wheel inwards.

Remove the screws.

Detach the panel.

Remove the marked part.

Remove the tape.

Remove the tape.

Use: 31299108, Double-sided tape

Vehicles with headlamp washers

Fold the wing liner to one side.

1. 
   

   Note! Tape the hose high up on the washer fluid reservoir to prevent washer fluid from coming out.

   
   

2. Take a piece of washer hose. Tie a knot in it and place it on the washer pump to prevent the washer fluid reservoir from emptying.

All vehicles

Turn the wheel inwards.

Remove the screws.

Detach the panel.

Remove the marked part.

Remove the tape.

Remove the tape.

Use: 31299108, Double-sided tape

Fold the wing liner to one side.

Locate the connector.

1. Depress the locking device.

2. Disconnect the connector.

Remove the clips.

Remove the clips.

Remove the screws.

Repeat on the other side.

The part is not to be reused.

Remove the screws.

Remove the clips.

Repeat on the other side.

The part is not to be reused.

Accessory installation

Repeat on the other side.

Repeat on the other side.

Repeat on the other side.

Connect the connectors.

Position/route the cable harness as illustrated.

Route the cable harness to the existing cable harness.

Attach the connector to the wiring harness.

The connector is not to be used.

Repeat on the other side.

Use: , Electrical tape

Place the Bumper Cover in position for installation.

Connect the connectors.

Vehicles with headlamp washers

Reinstall the removed parts in reverse order.

All vehicles

Reinstall the bumper.

Route the cable harness to the existing cable harness.

Reinstall the headlamp.

Remove the nuts.

Use special tool: T9512932, Tension spring

Fold the insulation to one side.

Use special tool: T9512932, Tension spring

Install the cable.

Use: , Electrical tape

Install the cable.

Raise the car.

Pull the wiring through.

Remove the tape.

Remove the Special Tool.

Pull the wiring through.

Insert the cable in to the passenger compartment, adjust the cable length out into the engine compartment and secure the rubber grommet.

Lower the car.

Fold the carpet to the side.

Connect the cable harness terminals in the connector as follows.

Disconnect the connector, if applicable.

Attach the connector to the wiring harness.

Use: , Electrical tape

The connector is not to be used.

Disconnect the connectors.

The part is not to be reused.

Install component that comes with the accessory kit.

Connect the connectors.

Connect the prerouted cable.

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31266964

Reinstall the removed parts in reverse order.