Installationsanweisung

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
V60 2013
V60 (-18) 2013

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
307564161.331428180, 31414382, 31316254, 31414381, 31316255
Alarm, Volvo Guard Alarm System




 
Equipment
IMG-242205
A0000162
IMG-239940
IMG-239664
IMG-334911

IMG-335536


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 
1
IMG-245980
 

Work is carried out in the same way on left and right-hand drive vehicles.

  • Turn the ignition key to position 0.


Note!

Wait at least three minutes before unplugging the connectors or removing other electrical equipment.


2
IMG-218298
 

Applies to vehicles where LEDs are to be replaced

  • Carefully bend loose the diode/sensor in the instrument panel.

3
IMG-218299
 

  • Unplug the connector from the LED and move aside.

4
IMG-218300
 

  • Get the new LED. Connect it to the connector and install it by pressing it in the instrument panel.

 
5
IMG-340333
 

6
IMG-340332
 

7
IMG-340338
 

8
IMG-340317
 

  • Remove air baffle.

 
9
IMG-340334
 

  • Remove the clips.

10
IMG-340342
 

11
IMG-340343
 

  • Disconnect the washer hose.

  • Take a piece of wiper hose. Tie a knot in it and install on the washer pump to prevent the washer fluid container from emptying.

12A
IMG-340398
12B
IMG-340344
 

Illustrations A and B


Note!

Get help from a colleague for this procedure.


  • Disconnect the washer hose.

  • Tape the hose high up on the washer fluid container to prevent washer fluid from running out.

13
IMG-340350
 

14
IMG-340352
 


Note!

The bonnet lock on the car's right side must be replaced with a new one from the kit. This applies to both right-hand and left-hand drive vehicles. The marking is found on both sides of the bonnet lock for right-hand and left-hand drive vehicles. Marking for relevant car model must be turned outwards.


  • Remove the screws in the hood lock and pull forwards.

15
IMG-340353
 

  • Disconnect the bonnet lock cable.

  • Place the bonnet lock to one side. A new one can be found in the kit.

16
IMG-340355
 

  • Release the cradle and pull it back to make room for the bonnet lock cable.

 
17A
IMG-340399
17B
IMG-340363
17C
IMG-340359
17D
IMG-340364
17E
IMG-340373
 

Image A, B, C, D and E

  • Take a new bonnet lock from the kit.

  • Insert the cable as illustrated and route it to the newly detached cradle on the left-hand side of the headlamp.

  • Press the connector into the existing hole.

18
IMG-340374
 

  • Connect the pre-routed connector to the routed cable. Found in the connection to the location.

19
IMG-340380
 

20
IMG-340382
 

21
IMG-340351
 

22
IMG-340384
 

23
IMG-340386
 

24
IMG-340387
 

25
IMG-335285
 

  • Disconnect the connector from its cradle.

  • Remove the cradle with clips, they will not be reused.

26
IMG-335289
 

  • Install the bracket with siren.

  • Tighten and torque tighten.

 
27
IMG-335290
 

  • Connect the siren.

28
IMG-340388
 

29
IMG-340386
 

30
IMG-340385
 

31A
IMG-340346
31B
IMG-340393
 

Illustrations A and B


Note!

Get help from a colleague for this procedure.


32
IMG-340338
 

33
IMG-340394
 

34
IMG-340395
 

35
IMG-340345
 

36
IMG-340318
 

37
IMG-340333
 

38
IMG-340332
 

39
IMG-242268
 

  • Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.