Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
C30 2010
D5244T9, D5244T13, B5254T7, D5244T8, B5244S4

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
312676031.530767057, 31373142
Electric engine block heater, 230V, 5 cyl




IMG-247803




 
Equipment
A0000162
A0000163
IMG-239664

IMG-332913

IMG-333598

IMG-365200

IMG-365191

IMG-247804

IMG-248565

IMG-265776


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Installing the front intake, applies to the S40/V50, -07

1
J8601099
 

Installing the front intake, applies to the S40/V50, -07

  • Use isopropanol P/N 1161721 to clean the bumper shell where the cutting template for the front engine block heater socket is to be secured.

  • Wipe dry.

2
J8601100
 

  • Apply a piece of tape vertically to the bumper cover. See the illustration.

3
J8601101
 

  • Remove the backing tape on the template from the kit.

  • Press the template onto the embossing on the bumper cover. The marking (1) on the template must be opposite the front edge of the tape. The marking (2) on the template must be in line with the curve (3) at the top edge of the embossing on the bumper cover.

4
J8601102
 

  • Take a sharp knife. First make a thin cut along the edges of the inside of the template. This provides a groove to follow. Then cut carefully out of the bumper cover.


    Note!

    Cut carefully. It is easy to slip with the knife and move outside the template.


  • Remove the template.

  • Install the protective cover for the front engine block heater socket from the kit. Check that it aligns. Adjust the hole using a knife or file as necessary.

  • Smooth off the hole edges. Remove any swarf.

5
J8000359
 

  • Remove the seven screws holding the engine splash guard and remove the guard.

6
J8601130
 

  • Remove the left and right-hand front wheels.

  • Remove the five screws holding the bumper cover in the wing liner on the left and right-hand sides.

7
J8601131
 

  • Remove the nut holding the left-hand fender liner to the front member.

  • Bend the front edge of the left-hand fender liner up over the brake calliper.

8
J8601087
 

  • Push in the centre of the five clips (1). Remove the clips.

  • Remove the two screws (2).

9A
J8601084
9B
J8903376
 

Illustration A

  • Remove the covers for the nozzles for the headlamp washers on the right and left-hand sides. Carefully grip the cover. Pull the cover out until the catch becomes accessible.

Illustration B

  • Press the catch up. Remove the cover. Do not damage the painted surfaces or the washer nozzles.

10
J8601086
 

  • Detach the ends of the bumper shell on the left and right-hand sides. Grasp the end of the bumper shell inside the fender liner. Carefully pull the end of the bumper shell so that the two catches on the inside release.

  • Remove the bumper cover and air baffle. Pull the bumper cover and air baffle forwards until the remaining catches under the lamps release.

  • Disconnect the connectors for the fog lamps if applicable.

11
J2900319
 

  • Press the protective cover (from the kit) into place in the hole cut in the bumper shell.

  • Insert the cable for the front engine block heater socket together with the ground lead from the kit through the protective cover.

12A
J2900320
12B
J2900321
 

Illustration A

  • Install the mounting and nut from the kit. Connect the connector to the front engine block heater socket. Use the connector as a counterhold when tightening.

Illustration B

  • Turn the connector for the front engine block heater socket so that the cover opens forwards. Tighten the front engine block heater socket to the bumper cover.

 

Installing the front intake, applies to the S40/V50, MY 07-

13
J8000359
 

Installing the front intake, applies to the S40/V50, MY 07-

  • Remove the seven screws from the engine splash guard.

  • 14
    J8601130
     

    • Remove the left front wheel.

    • Remove the five screws holding the bumper cover in the wing liner on the left and right-hand sides.

    15
    IMG-265763
     

    • Remove the four screws.

    16
    J8601087
     

    • Push in the centre of the five clips (1). Remove the clips.

    • Remove the two screws (2).

    17
    J8601084
     

    • Remove the covers for the nozzles for the headlamp washers on the right and left-hand sides. Carefully grip the cover. Pull the cover out until the catch becomes accessible.

    18
    J8903376
     

    • Press the catch up. Remove the cover. Do not damage the painted surfaces or the washer nozzles.

    19
    J8601086
     

    • Detach the ends of the bumper cover on the left and right-hand sides. Grasp the end of the bumper cover inside the wing liner. Carefully pull the end of the bumper cover so that the two catches on the inside release.

    • Remove the bumper cover and air baffle. Pull the bumper cover and air baffle forwards until the remaining catches under the lamps release.

    • Disconnect the connectors for the fog lamps and parking assistance if applicable.

    20
    IMG-265777
     

    • Cut out the template by cutting along the outer edges of the dotted and solid line.

    • place the template with the dotted section on the existing marking (periphery) on the bumper. Mark according to the new, slightly recessed marking.

    • Cut off the upper dotted section of the template and finish the new marking all the way around.

    21
    IMG-265778
     

    • Using a sharp knife, first make a thin cut along the edges of the new marking inside of the bumper cover. Then carefully cut out the bumper cover hole.


      Note!

      Cut carefully. It is easy to slip with the knife and move outside the markings.


    • Install the protective cover for the front engine block heater socket from the kit. Check that it aligns. Adjust the hole using a knife or file as necessary.

    • Smooth off the hole edges. Remove any swarf.

    22
    IMG-265779
     

    • Take the protective cover from the kit and press it into the hole cut in the bumper cover.

    • Take the cable for the front engine block heater socket with ground lead from the kit and thread them through the protective cover.

    23
    IMG-265781
     

    • Install the mounting and nut from the kit. Connect the connector to the front engine block heater socket. Use the connector as a counterhold when tightening.

    24
    IMG-265782
     

    • Turn the front intake connector so that the cover opens forwards.

    • Tighten the front engine block heater socket to the bumper shell.

     

    Installing the front intake (C70)

    25
    IMG-225653
     

    Installing the front intake (C70)

    • Install the protective film along the outside of the bumper's left-hand corner.

    26
    IMG-225652
     

    • Remove the covers for the nozzles for the headlamp washers on the right and left-hand sides. Carefully grip the cover. Pull the cover out until the catch becomes accessible.

    27
    J8903376
     

    • Press the catch up. Remove the cover. Do not damage the painted surfaces or the washer nozzles.

    28
    IMG-225651
     

    • Remove the screws to the air baffle.

    29
    IMG-227800
     

    • Press in the centre of the clips (1) and remove them. Remove the screws (2).

    30
    J8601130
     

    • Remove the left and right-hand front wheels.

    • Remove the five screws holding the bumper cover in the wing liner on the left and right-hand sides.

    31
    IMG-225649
     

    • Detach the right and left-hand ends of the bumper.

    • Grip the bumper from the inside and pull it forward in order to detach the two holders under the headlamps.

    • Remove the bumper, unplug the connectors for the fog lamps and place the bumper on a surface that does not damage the paintwork.


      Hint

      Removal of the bumper is facilitated if carried out by two people.


    32
    IMG-225647
     

    • Unscrew and remove the bolt and nuts securing the wing liner.

    • Remove the wing liner.

    33
    IMG-225646
     

    • Remove the screws holding the engine splash guard and remove the guard.

    34
    IMG-225645
     

    • Locate the pre-marking on the inside of the bumper cover on the left-hand side of the car.

    • Use a Ø 10mm (3/8") drill bit to drill inside the four corners of the marking area.

    • Take a sharp knife and carefully cut out the pre-marked area in the bumper cover on the left-hand side of the car.


      Note!

      Cut carefully. It is easy to slip with the knife and move outside the markings.


    35
    IMG-225644
     

    • Remove swarf and smaller irregularities with a file. Do not damage the paintwork and follow the pre-marking accurately.

    • Install the box for the front engine block heater socket from the kit. Check that it aligns. Adjust the hole using a knife or file as necessary.

    • File down the edges of the holes.

    36
    IMG-225643
     

    • Take the cable harness with front socket and box from the kit.

    • Route the cable through the box and fit the connector.

    • Pull in the cable and align the box in the hole made in the bumper.

    37
    IMG-225642
     

    • Take the bracket and the large plastic nut from the kit and thread the cable harness through them.

    • Pull forward the bracket to the inside of the bumper and tighten the box with the large plastic nut. Plug the electrical connector into the front socket as a counterhold for when the latter is tightened.

    38
    IMG-225641
     

    • Check that the connector cover works as intended.

     

    Installing the front intake (C70) 2010-

    39
    IMG-332924
     

    Installing the front intake (C70) 2010-

    • Clean the bumper cover where the wing template is to be positioned.

    • Wipe dry.

    40
    IMG-332914
     

    • Find the template for C70 MY 2010 in the installation instructions. Cut it out following the dotted lines.

    41
    IMG-332916
     

    • Position the templates following the curves of the surface between the lower grille and panel for the fog lamps and tape it according to the image.

    • Take a sharp knife. First make a thin cut along the edges of the inside of the template. This provides a groove to follow. Then cut carefully out of the bumper cover.


    Note!

    Cut carefully. It is easy to slip with the knife and move outside the template.


    • Remove the template.

    • Install the protective cover for the front engine block heater socket from the kit. Check that it aligns. Adjust the hole using a knife or file as necessary.

    • Smooth off the hole edges. Remove any swarf.

    42
    J8601130
     

    • Remove the left and right-hand front wheels.

    • Remove the five screws holding the bumper cover in the wing liner on the left and right-hand sides.

    43
    J8601131
     

    • Remove the nut holding the left-hand fender liner to the front member.

    • Bend the front edge of the left-hand fender liner up over the brake calliper.

    44
    IMG-225652
     

    • Remove the covers for the nozzles for the headlamp washers on the right and left-hand sides. Carefully grip the cover. Pull the cover out until the catch becomes accessible.

    45
    IMG-332933
     

    • Carefully pull the hook to the side and remove the cover. Repeat on the other side.

    46
    IMG-227800
     

    • Press in the centre of the clips (1) and remove them. Remove the screws (2).

    47
    IMG-225649
     

    • Detach the right and left-hand ends of the bumper.

    • Grip the bumper from the inside and pull it forward in order to detach the two holders under the headlamps.

    • Remove the bumper, unplug the connectors for the fog lamps and place the bumper on a surface that does not damage the paintwork.


    Hint

    Removal of the bumper is facilitated if carried out by two people.


    48
    IMG-332938
     

    • Press the protective cover (from the kit) into place in the hole cut in the bumper shell.

    • Insert the cable for the front engine block heater socket together with the ground lead from the kit through the protective cover.

    49A
    IMG-332939
    49B
    IMG-332943
     

    A

      Illustration A

    • Install the mounting and nut from the kit. Connect the connector to the front engine block heater socket. Use the connector as a counterhold when tightening.

      Illustration B

    • Turn the front intake connector so that the cover opens outwards to the side.

    • Tighten the front engine block heater socket to the bumper shell.

    B

    50
    IMG-225646
     

    • Remove the screws holding the engine splash guard and remove the guard.

    51
    IMG-247823
     

    Installing the front intake, applies to the C30

    • Use isopropanol P/N 1161721 to clean the bumper shell where the cutting template for the front engine block heater socket is to be secured.

    • Wipe dry.

    52
    IMG-248765
     

    • Find the template for the C30 in the installation instructions. Cut it out following the dotted lines.

    53A
    IMG-249205
    53B
    IMG-247824
     

    Illustration A

    • Position the template in the corner of the bumper cover embossing and align it against the upper edge of the right-hand edge.

    Illustration B

    • Tape the template to the bumper cover.

    54
    IMG-247825
     

    • Take a sharp knife. First make a thin cut along the edges of the inside of the template. This provides a groove to follow. Then cut carefully out of the bumper cover.


      Note!

      Cut carefully. It is easy to slip with the knife and move outside the template.


    • Remove the template.

    • Install the protective cover for the front engine block heater socket from the kit. Check that it aligns. Adjust the hole using a knife or file as necessary.

    • Smooth off the hole edges. Remove any swarf.

    55
    J8000359
     

    • Remove the seven screws from the engine splash guard.

    56
    IMG-247826
     

    • Remove the left and right-hand front wheels.

    • Remove the four screws holding the bumper cover in the wing liner on the left and right-hand sides.

    57
    J8601131
     

    • Remove the nut holding the left-hand fender liner to the front member.

    • Bend the front edge of the left-hand fender liner up over the brake calliper.

    58
    J8601087
     

    • Push in the centre of the five clips (1). Remove the clips.

    • Remove the two screws (2).

    59A
    J8601084
    59B
    J8903376
     

    Illustration A

    • Remove the covers for the nozzles for the headlamp washers on the right and left-hand sides. Carefully grip the cover. Pull the cover out until the catch becomes accessible.

    Illustration B

    • Press the catch up. Remove the cover. Do not damage the painted surfaces or the washer nozzles.

    60A
    IMG-248768
    60B
    IMG-247843
     

    Illustration A

    • Apply a piece of tape to the panel of the wing edge to protect it.

    • Carefully pry off the corner of the bumper cover using a weatherstrip tool until the three hooks on the inside release.

    Illustration B

    • Remove the bumper cover with air baffle by grasping the ends and pulling forwards until the remaining hooks under the lamps release.


      Note!

      Get help from a colleague for this procedure.


    • Disconnect the connectors for the fog lamps or parking assistance if applicable.

    • Remove the pieces of tape from the edges of the wing.

    61
    IMG-247844
     

    • Press the protective cover (from the kit) into place in the hole cut in the bumper shell.

    • Insert the cable for the front engine block heater socket together with the ground lead from the kit through the protective cover.

    62A
    IMG-247845
    62B
    IMG-247846
     

    Illustration A

    • Install the mounting and nut from the kit. Connect the connector to the front engine block heater socket. Use the connector as a counterhold when tightening.

    Illustration B

    • Turn the connector for the front engine block heater socket so that the cover opens backwards. Tighten the front engine block heater socket to the bumper cover.

    63
    IMG-332918
     

    Installing the front intake, applies to the C30 2010-

    • Remove the front wheels.

    64
    IMG-331946
     

    65
    IMG-331947
     

    • Remove the screws from in the right and left fender liner and the plastic nut in the left fender liner.

    66
    IMG-331948
     

    67
    IMG-332920
     

    • Carefully pry off the panel at the lower edge and remove it. Place to one side. A new one can be found in the kit.

    68A
    IMG-331989
    68B
    IMG-331990
     

    A

    • Take a new panel, front intake cable with washer and nut from the kit.


    Note!

    The washer must be positioned as illustrated.


    • Insert the cable and ground lead through to the engine heater. Ensure the connector is turned so that the cover's sides are parallel with the plates in the panel and that the cover opens from the panel's left-hand side (Image B).

    • Tighten the connector.

    B

    69
    IMG-331991
     

    • Insert the cable through the oval smaller hole on the rear of the panel.

    • Press the panel into place.

    70
    IMG-225640
     

    Applies to all car models where the bumper cover is removed

    • Reinstall the bumper cover. Use the five clips and the two screws at the top edge. Ensure that the air baffle is correctly positioned in its mounting.

    • Press in so that the clips under the headlamps fasten.

    • Reconnect the connectors for the fog lamps and parking assistance if applicable.


    Hint

    Installation of the bumper is facilitated if carried out by two people.


     

    Cable routing

    71
    J2900313
     

    Cable routing

    • Install three clips from the kit on the panel edge on the underside of the left front member.

    72
    IMG-360291
     

    • Route the front intake cable from the front edge of the washer fluid reservoir, along the bottom edge of the front member and over the drive shaft.

    • Press the cable into the previously installed clips.

    73
    IMG-365113
     

    • Install steel clips as illustrated.

    • Install the cable harness and secure it with cable tie in the subframe. Insert the cable into the engine compartment a little.

    74
    J2900297
     

    • Clamp the cable in the hole in the bracket for the front left radiator mounting. Use a tie strap (1) from the kit.

    75
    J2900298
     

    • Drill a Ø4 mm (5/32 ”) hole for the ground lead, on the outside of the left-hand front member, approximately as illustrated.

    • Treat the edges of the holes using a rust-proofing agent.

    76
    J2900299
     

    • Secure the ground lead in the drilled hole. Use the screw and toothed washer from the kit.

    • Affix the excess length of ground lead at the existing clips.

    77
    IMG-232644
     

    • Install three clips from the kit on the front edge of the panel above the windscreen wiper motor.

    • Guide the cable up to the top of the engine compartment to the position illustrated.

    78A
    IMG-232645
    78B
    J2900316
     

    Illustration A

    • Press the front intake cable into the clips. Guide down the cable at point (1) and route down through the engine compartment (behind the AC pipes) down to the strut in the right link arm mounting.

    Illustration B

    • Clamp in the cable, from the top of the engine compartment and down, using a cable tie (Image B).


      Note!

      Do not clamp the cable directly to AC pipes, fuel lines, brake pipes or power steering hoses and pipes. Make sure the cable does not chafe against sharp edges or moving parts in the engine compartment.


    79
    D3601932
     

    • Lubricate the O-rings on all cables for the engine block heater and if the car is to have a passenger compartment connector/timer relay, also lubricate the O-rings on these with low temperature grease P/N 1161417.


      Note!

      Do not get any grease on the surfaces of the connector.


    80
    J2900302
     

      Applies to cars where the engine block heater and passenger compartment connector socket are installed at the same time

    • Take the bracket and the rubber guard from the kit for the passenger compartment connector socket. Press the rubber guard on to the bracket.

    81
    J2900296
     

      Applies to cars where the engine block heater and passenger compartment connector socket are installed at the same time

    • Tighten the junction connector at the bracket (included in the kit for the passenger compartment connector socket) in the position illustrated. Use the screw, toothed washer and nut from the kit. The bracket must be parallel to the length of the junction connector.

    • Position (1) cable for the engine block heater

      Position (2) cable for the passenger compartment socket

      Position (3) cable from the front engine block heater socket.

    82
    J2900303
     

      Applies to cars where the engine block heater and timer relay are installed at the same time

    • Tighten the timer relay at the bracket (purchased separately) in the position illustrated. Use the screw, toothed washer and nut from the kit. The bracket must be parallel to the length of the timer relay.

    • Connect the connector on the long cable harness (from the kit) to the timer relay.

    • Press the rubber plug (1), part no. 346509, (purchased separately) into place on the free socket in the timer relay. Use butyl tape to secure the rubber plug.

    • Position (2) cable for the engine block heater

      Position (3) cable from the front engine block heater socket.

    83
    J2900304
     

      Applies to cars where the passenger compartment connector socket and the timer relay are installed at the same time

    • Tighten the timer relay at the bracket (purchased separately) in the position illustrated. Use the screw, toothed washer and nut from the kit. The bracket must be parallel to the length of the timer relay.

    • Connect the connector on the long cable harness (from the kit) to the timer relay.

    • Position (1) cable for the passenger compartment socket

      Position (2) cable for the engine block heater

      Position (3) cable from the front engine block heater socket.

    84
    J2900292
     

    • Connect the short cable from the kit to the engine block heater, to the routed cable (1) from the front socket. (When fitting junction connector/timer relay at the same time, the cable from the front socket is connected to the single outlet on the junction connector/timer relay instead. Refer to the installation instructions for passenger compartment socket/timer relay).

    • Firmly press the cable junction together.

    85
    J2900293
     

    • Press a locking sleeve (from the kit) over the cable splice.

    86
    J2900294
     

    • Take a double tie strap from the kit. Install the double tie strap around the stay and the cable splice. Ensure that the splice is secured in the centre of the strut. Tighten the double clamp properly.

     

    Installing the engine block heater

    87
    J2900295
     

    Installing the engine block heater

    • Remove the cover on the radiator expansion tank.

    • Unscrew the drain nipple in the radiator pipe above the oil cooler in front of the right drive shaft. Drain the coolant.

    88
    IMG-232646
     

    • Detach the hose clips of the left oil cooler hose and remove the hose.

    • Put the hose to the side.

    89
    IMG-214121
     

    • Take a bracket, two bolts and washers from the kit. Fasten the bracket in the existing holes on the left side of the oil cooler.


      Note!

      The screws are self-tapping so it may be slow inserting them. Make sure that the screws are centred straight into the holes, so that the screw heads are flat against the bracket.


    90
    IMG-214122
     

    • Take the heater, rubber-clad clamp and bolt from the kit. Fasten the heater with the clamp. The connections should point straight back.

    91
    IMG-214124
     

    • Take the long hose and two hose clips from the kit. Connect the hose between the radiator pipe and upper heater socket.

    • Tighten the hose clips.

    92
    IMG-234800
     

      Applies to cars with diesel engine

    • Cut the remaining hose 15 mm (19/32") in the long, straight end.

    93
    IMG-214123
     

    • Take the hose and two hose clips from the kit and connect them between the oil cooler and lower heater socket. The end with the long, straight/cut part should be connected to the oil cooler (see previous illustration).

    • Tighten the hose clips.

    94
    IMG-235624
     

    • Take the radiation shield from the kit and thread on the joint cable of the heater.

    95
    IMG-235626
     

    • Connect the short electrical cable (which was routed earlier) to the engine block heater. Press it firmly into the engine block heater connection.

    • Press in a locking sleeve from the kit over the cable splice.

    96
    IMG-235629
     

    • Pull the radiation shield up so that it fully covers the connector on the heater.

    • Take the grey tie strap kit and clamp the radiation shield by the heater in the upper edge.

    97A
    IMG-235630
    97B
    IMG-236480
    97C
    IMG-365515
     

    Illustration A applies to the diesel engine

    • Fasten the heater cable to the turbocharger pipe using a double tie strap from the kit.

    Illustration B applies to petrol engines without turbo

    On cars with petrol engine without turbo, route the cable with radiation shield below the power steering hoses/pipes.

    • Fit a double tie strap to the two steering gear pipes and the cable with radiation shield.

    • Fit the double tie strap over the hoses' press sleeves.

    Illustration C applies to petrol engine with turbo

    On cars with petrol engine and turbo, route the cable with radiation shield under the power steering hoses/pipes and under the turbo pipe.

    • Fit a double tie strap to turbocharger pipe and the cable with radiation shield.

    98
     

    • Reinstall the left-hand fender liner. Tighten the fender liner to the left-hand side member.

    • Tighten the two wing liners to the bumper cover on the right and left-hand sides.

    • Fill with coolant, run the engine to operating temperature, bleed the cooling system and check that there are no leaks.

    • Reinstall the engine splash guard.

    • Reinstall the front wheels and torque tighten the wheel nuts:

      Step 1: Wheel to wheel hub, 20 Nm

      Step 2: Wheel to wheel hub, 110 Nm