Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

There may be parts in the accessories kit that are not needed for this installation.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

7. Used for accessory components.

Removal

Move marked component forward.

Remove the screws.

The image shows seat without upholstery.

Release the locks.

Remove the marked part.

Remove the marked part.

Release the locks.

Remove the marked detail/details.

Accessory installation

Install component that comes with the accessory kit.

A click confirms that the component is in the correct position.

Assemble the components according to image.

Repeat on the other side.

Check that the component has locked in its position.

Pull the wiring harness through.

Compare with upholstery and head restraint on the other front seat.

Compare with upholstery and head restraint on the other front seat.

If adjustment is necessary, follow the procedure described in the method step below.

Applies when installing on right-hand seat.

Install component that comes with the accessory kit.

Install component that comes with the accessory kit.

Install component that comes with the accessory kit.

Connect the connectors.

Connect the connectors.

Install component that comes with the accessory kit.

Connect the connectors.

Position/route the cable as illustrated.

Tighten the cable tie.

Applies when installing on left-hand seat.

Install component that comes with the accessory kit.

Install component that comes with the accessory kit.

Install component that comes with the accessory kit.

Connect the connectors.

Connect the connector.

Install component that comes with the accessory kit.

Connect the connectors.

Position/route the cable as illustrated.

Tighten the cable tie.

On both sides.

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Move marked component backwards.

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Fold marked part aside.

1. Release the connector's catch.

2. Release the lock.

3. Disconnect the connector.

Unhook the cable harness clips.

Remove the marked part.

Remove the screw.

Lift marked component out.

Remove the marked part.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Reinstall the removed part.

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

Repeat the steps when removing on opposite side.

Repeat the steps when installing accessories on opposite side.

Removal

Remove the screws.

Fold marked part aside.

1. 
   Tightening torque: M6 , 10 Nm
   

2. 
   Tightening torque: M5 , 5 Nm
   

Release the lock.

Remove the marked part.

Remove the marked part.

Use hands only.

Fold marked part aside.

Remove the screw.

Tightening torque: Seat belt guide, to Bracket , 4.4 Nm

Remove the panel.

Use hands only.

Fold marked part aside.

Release the catch.

Remove the marked part.

Remove the panel.

Use hands only.

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Remove the marked part.

Detach the panel.

Remove the panel.

Repeat the steps when installing accessories on opposite side.

Open the tailgate.

Remove the marked part.

Remove the screw.

Tightening torque: Cargo anchor, to body , 13 Nm

Repeat on the other side.

Lift the marked component up

Release the lock.

Fold marked part aside.

Remove the marked part.

Vehicles with spare wheel

Release the lock.

Loosen the marked detail.

Remove the marked part.

All vehicles

Vehicles with keyless entry

1. Release the lock.

2. Fold marked part aside.

Release the catch.

Loosen the component indicated. Do not remove it.

All vehicles

Repeat on the other side.

Remove the screw.

Tightening torque: Cargo anchor, to body , 13 Nm

Repeat on the other side.

Remove the screws.

Remove the marked part.

Remove the panel.

Disconnect the connectors.

Repeat on the other side.

Accessory installation

Install component that comes with the accessory kit.

Clean the surface.

Use: 1161721, Isopropanol

Assemble components that come with the accessory kit.

When installing Velcro tape the surface must maintain a temperature of at least +20 ° C (68°F).

Clean the surface.

Use: 1161721, Isopropanol

Install component that comes with the accessory kit.

Install the marked component.

Position wire as illustrated.

Install the cables.

Use a cable tie

Vehicles with towbar

Disconnect the connector.

Connect the connector.

Connect the connector.

Place the cable tie as illustrated.

Vehicles without tow hitch.

Connect the connector.

Secure the connectors.

All vehicles

Remove the marked part.

Remove the nut.

Fold marked part aside.

Release the catches.

Fold marked part aside.

Fold marked part aside.

Remove the marked part.

Connect the cable.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Reinstall the removed part.

Reinstall the removed part.

Install components that come with the accessory kit.

Remove the nut.

Connect the ground cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Remove the marked part.

Release the lock.

Remove the marked part.

Remove the marked part.

Connect the cable.

Reinstall the removed part.

Reinstall the removed part.

Reinstall the clips.

Reinstall the removed part.

Remove the nut.

Connect the ground cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Position/route the cable as illustrated.

Use a cable tie

Position/route the cable as illustrated.

Use a cable tie

Position/route the cable as illustrated.

Use a cable tie

Position/route the cable as illustrated.

Use a cable tie

Install the marked component.

Connect the connectors.

Position/route the cable as illustrated.

Use a cable tie

Install the marked component.

Connect the connectors.

Installation

Reinstall the removed parts in reverse order.

Check for correct operation.