| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-363036 |
|
| | Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | Disconnecting the battery |
| | IMG-394535 |
|
| | |
| | IMG-425513 |
|
| | Remove the battery's negative cable. Tightening torque: Battery cable for battery
, 6 Nm
|
| | |
| | IMG-422428 |
|
| | |
| | IMG-422431 |
|
| | |
| | IMG-404717 |
|
| | Loosen the clip. Connect the connector. |
| | IMG-404771 |
|
| | Disconnect the connectors. |
| | IMG-404745 |
|
| | Remove the screws. Remove the marked part. Tightening torque: M6
, 10 Nm
|
| | IMG-404751 |
|
| | |
| | IMG-404757 |
|
| | Remove the nut. Fold marked part aside. Tightening torque: Nut (M6), to BCSM
, 10 Nm
|
| | IMG-404765 |
|
| | |
| | IMG-404800 |
|
| | Remove the nuts. Tightening torque: Nut (M8), to BCSM
, 24 Nm
|
| | IMG-404802 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-404807 |
|
| | |
| | IMG-404810 |
|
| | |
| | IMG-404820 |
|
| | Release the locks. Fold marked part aside. |
| | IMG-404825 |
|
| | Remove the screws. Remove the marked part. |
| | IMG-422562 |
|
| | |
| | IMG-422563 |
|
| | |
| | IMG-382204 |
|
| | Remove the clips. Remove the screws. Remove the marked part. |
| | IMG-387143 |
|
| | |
| | IMG-392033 |
|
| | |
| | IMG-391976 |
|
| | Note! Close the drain cock after the coolant has drained. |
Place a container under the car. Drain the coolant. |
| | IMG-422546 |
|
| | Loosen the hose clamp. Remove the marked part. |
| | IMG-422549 |
|
| | Loosen the hose clamp. Fold marked part aside. |
| | IMG-422547 |
|
| | Loosen the hose clamp. Remove the marked part. |
| | IMG-422554 |
|
| | Remove the screw. Fold marked part aside. |
| | IMG-422561 |
|
| | |
| | IMG-404740 |
|
| | |
| | IMG-422632 |
|
| | |
| | IMG-422635 |
|
| | |
| | IMG-404981 |
|
| | Note! Use suitable paper to absorb any escaping fluid. |
Release the lock. Undo the hose from the connection.
|
| | IMG-404982 |
|
| | Note! Use suitable paper to absorb any escaping fluid. |
Release the lock. Loosen the hose clamp. Remove the marked part.
The part is not to be reused. |
| | IMG-404983 |
|
| | |
| | IMG-403425 |
|
| | Remove the marked part. Use: Pliers
|
| | IMG-403428 |
|
| | |
| | IMG-382280 |
|
| | |
| | IMG-382210 |
|
| | Remove the screws. Remove the clips. |
| | IMG-382211 |
|
| | |
| | IMG-391565 |
|
| | |
| | IMG-391573 |
|
| | Release the catches. Fold marked part aside. |
| | IMG-391924 |
|
| | Remove the nut. The part is to be reused. |
| | IMG-412196 |
|
| | |
| | IMG-412198 |
|
| | |
| | IMG-412199 |
|
| | |
| | IMG-428776 |
|
| | |
| | IMG-428775 |
|
| | Remove the screw. Release the catches. Remove the marked part. |
| | |
| | IMG-425328 |
|
| | Measure and mark as illustrated. |
| | IMG-425329 |
|
| | |
| | IMG-425330 |
|
| | Adjust the hole with a file or knife as necessary. |
| | |
| | IMG-422409 |
|
| | |
| | IMG-430245 |
|
| | |
| | IMG-425341 |
|
| | |
| | IMG-428777 |
|
| | Reinstall the removed part. |
| | IMG-425360 |
|
| | |
| | IMG-404695 |
|
| | Connect the prerouted cable. |
| | IMG-404700 |
|
| | Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-391930 |
|
| | Press until a click is heard. |
| | IMG-422412 |
|
| | Connect the connectors. Install the catch. |
| | IMG-425365 |
|
| | |
| | IMG-425366 |
|
| | Install the clip(s). Tighten the cable tie. |
| | IMG-422387 |
|
| | |
| | IMG-422415 |
|
| | Install the clip(s). Tighten the cable tie. |
| | IMG-422417 |
|
| | Install the clip(s). Place the component where indicated in the graphic. |
| | IMG-422421 |
|
| | Install the clip(s). Tighten the cable tie. |
| | IMG-422729 |
|
| | Install component that comes with the accessory kit. |
| | IMG-422728 |
|
| | Clamp using the grey cable tie. |
| | IMG-422424 |
|
| | Install the clip(s). Clamp using the grey cable tie. |
| | IMG-405117 |
|
| | Caution! Cut carefully to avoid unintentional damage or personal injury. |
Remove the marked part. |
| | IMG-405119 |
|
| | Install component that comes with the accessory kit. Tightening torque: M6
, 10 Nm
|
| | IMG-405120 |
|
| | Install component that comes with the accessory kit. Tighten the hose clamp. |
| | IMG-405122 |
|
| | Install component that comes with the accessory kit. Note the position. |
| | IMG-405123 |
|
| | Locate relevant marking. Install component that comes with the accessory kit. |
| | IMG-405135 |
|
| | Install component that comes with the accessory kit. A click confirms that the component is in the correct position. |
| | IMG-405145 |
|
| | Note the position. Install component that comes with the accessory kit. |
| | IMG-405203 |
|
| | Install the hose. Install the clips as illustrated. |
| | IMG-405206 |
|
| | Reinstall the removed part. |
| | IMG-405141 |
|
| | Note the position. Install component that comes with the accessory kit. Tightening torque: M5
, 5 Nm
|
| | IMG-405150 |
|
| | Install the hose. Tighten the hose clamp. |
| | IMG-391915 |
|
| | Caution! No grease on contact surfaces. |
Lubricate the O-ring. |
| | IMG-422695 |
|
| | Install component that comes with the accessory kit. Install the catch. |
| | |
| | IMG-404661 |
|
| | Note! Always follow the manufacturer's instructions when handling the equipment. |
Use special tool: T9512955, Cover
Use special tool: T9512957, Coolant Reservoir
Fill with coolant and run the engine to operating temperature. |
| | Reinstall the removed parts in reverse order. |
| | IMG-405228 |
|
| | Note! Make sure to follow the sequence indicated. |
Tightening torque: Aluminum wheel rim to wheel hub Stage 1:
4 Nm Stage 2:
50 Nm Stage 3:
140 Nm
|