Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

There may be parts in the accessories kit that are not needed for this installation.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Removal

Remove the panel.

Fold marked part aside.

Remove the screw.

Tightening torque: Seat belt guide, to Bracket , 4.4 Nm

Remove the panel.

Use hands only.

Release the catch.

Remove the marked part.

Remove the panel.

Use hands only.

Remove the panel.

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Remove the screw.

Tightening torque: M8 , 24 Nm

Remove the screw.

Tightening torque: Safety belt lower anchor to body (rear) , 40 Nm

Repeat the steps when removing on opposite side.

Remove the marked part.

Repeat on the other side.

Remove the screw.

Tightening torque: M6 , 10 Nm

Repeat on the other side.

Remove the marked part.

Remove the screws.

Remove the marked part.

Remove the panel.

Disconnect any connector(s).

Remove the screws.

Remove the marked part.

Repeat the steps when removing on opposite side.

Replace Fixed side windows according to service information in VIDA:

Information/ Repair/ Removal, replacement, installation/ 8 Body and interior/ 84 Exterior trim, glass, weatherstrips/ 844 glass for side doors and window/ Fixed side window

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Remove the panel.

Disconnect the connector, if applicable.

Remove the screws.

Remove the panel.

Release the lock.

Repeat on the other side.

Remove the marked part.

Remove the panel.

Disconnect the connector, if applicable.

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Disconnect the connector.

Remove the panel.

Disconnect the connector.

Remove the connector from its attachment.

Remove the screw.

Remove the screw.

Remove the panel.

Disconnect the connector.

Remove the screw.

Remove the screw.

Cars with automatic transmissions

Use special tool: T9512943, L-hook

Cars with manual transmissions

Use special tool: T9997077, Jimmy bar

Use special tool: T9997077, Jimmy bar

Release the locks.

Loosen the marked detail/details.

All vehicles

Remove the marked part.

Remove the screws.

Remove the cable tie(s).

Disconnect the connectors.

Remove the screws.

Remove the marked part.

Disconnect the connectors.

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Disconnect the connector.

Unhook the cable harness clips.

Remove the screws.

Fold marked part aside.

1. 
   Tightening torque: M6 , 10 Nm
   

2. 
   Tightening torque: M5 , 5 Nm
   

Remove the marked part.

Remove the marked part.

Remove the marked part.

Detach the panel.

Remove the panel.

Accessory installation

Remove the nut.

Place the component where indicated in the graphic.

Install the nuts

Install the nut.

Tightening torque: M6 , 10 Nm

Adjust the component to a horizontal position.

Connect the connectors.

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Remove the screws.

Remove the marked part.

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Remove the nut.

Connect the prerouted cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Install the cables.

Use a cable tie

Remove the screw.

Release the lock.

Fold marked part aside.

Remove the battery's negative cable.

Remove the marked part.

Remove the nut.

Fold marked part aside.

Release the catches.

Fold marked part aside.

Remove the marked part.

Vehicles with Alcohol Analysing Start Inhibitor

Remove the marked part.

Use special tool: T9512631, Terminal removal tool (Color code: Brown)

Use special tool: T9512620, Stripping tool (for wiring)

Use special tool: T9512785, Crimping tool (included in 9512669)

Use special tool: T9512777, Hot-air gun

All vehicles

Connect the prerouted cable.

Reinstall the removed part.

Install the cable.

Use a cable tie

Reinstall the removed part.

Install component that comes with the accessory kit.

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Fold marked part aside.

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Position/route the cables as illustrated.

Use a cable tie

Remove the marked part.

Disconnect the connector.

Alternative 1

Connect the prerouted cables.

Alternative 2

Depress the secondary lock.

Connect the prerouted cables.

All vehicles

Use tape

Attach the connector to the wiring harness.

Use a cable tie

Install the cable.

Use a cable tie

Install the cable.

Use a cable tie

Position/route the cable as illustrated.

Connect the connector.

Tear off the excess foam tape.

Connect the connector.

Installation

Connect the connectors.

Reinstall the removed part.

Reinstall the screws.

Connect the connectors.

Install the wiring harness.

Use a cable tie

Accessory installation

Connect the connector.

Position/route the cable as illustrated.

Use tape

Position/route the cable as illustrated.

Use tape

Position/route the cable as illustrated.

Use tape

Position/route the cable as illustrated.

Use tape

Position/route the cable as illustrated.

Use tape

Position/route the cable as illustrated.

Use tape

Position/route the cable as illustrated.

Use tape

Install component that comes with the accessory kit.

Install the screw.

Tightening torque: M6 , 10 Nm

Connect the prerouted cable.

Connect the connector.

Connect the connector.

Use tape

Route the wire adjacent to existing wirings.

Install the cable.

Use tape

Route the wire adjacent to existing wirings.

Install the cable.

Use tape

Route the wire adjacent to existing wirings.

Install the cable.

Use tape

Position/route the cable as illustrated.

Install the cable.

Use tape

Position/route the cable as illustrated.

Install the cable.

Use tape

Position/route the cable as illustrated.

Install the cable.

Use tape

Install component that comes with the accessory kit.

Install the screw.

Tightening torque: M6 , 10 Nm

Connect the prerouted cable.

Connect the connector.

Connect the connector.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Use a drill with the stated size

Use a drill with the stated size

Install the nut.

Tighten the nut.

Use hands only.

Connect the prerouted cable.

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.

Installation

Reinstall the removed parts in reverse order.

Place the manual for this accessory in a suitable location in the car.