| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-400010 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components. Used for accessory components.
|
| | |
| | IMG-382528 |
|
| | Open the hood. Raise the car. |
| | IMG-403416 |
|
| | |
| | IMG-403425 |
|
| | Remove the marked detail/details. Use: Pliers 31423632
|
| | IMG-403428 |
|
| | |
| | IMG-403430 |
|
| | |
| | IMG-398442 |
|
| | Remove the screws. Remove the clip. |
| | IMG-398445 |
|
| | Remove the nuts. Remove the screw. |
| | IMG-398443 |
|
| | Remove the screws. Remove the marked part. |
| | IMG-398446 |
|
| | Remove the screw. Remove the clips. |
| | Vehicles with air suspension |
| | IMG-406660 |
|
| | |
| | |
| | IMG-397073 |
|
| | |
| | IMG-462648 |
|
| | Remove the screws. Remove the marked part. |
| | IMG-382204 |
|
| | Remove the screws. Remove the clips. Remove the marked part. |
| | IMG-462652 |
|
| | |
| | IMG-465256 |
|
| | Remove the screws. Remove the marked part. Remove the cable harness clips. |
| | |
| | IMG-462844 |
|
| | Locate relevant marking. Remove the decal. |
| | IMG-398765 |
|
| | |
| | IMG-399407 |
|
| | |
| | IMG-462655 |
|
| | Install component that comes with the accessory kit. Check that the flange of the part is in full contact with bumper cover. Adjust the hole with a file or knife as necessary. |
| | IMG-462658 |
|
| | Install component that comes with the accessory kit. |
| | IMG-462661 |
|
| | |
| | IMG-462662 |
|
| | Note! Do not fully tighten the nut yet. |
Install components that come with the accessory kit. |
| | IMG-462664 |
|
| | Install component that comes with the accessory kit. This is used as a counterhold. |
| | IMG-462663 |
|
| | |
| | IMG-462688 |
|
| | Position/route the cable as illustrated. |
| | IMG-462687 |
|
| | |
| | IMG-462674 |
|
| | Release the catches. Fold marked part aside. |
| | IMG-462682 |
|
| | Remove the nut. The part is to be reused. |
| | IMG-462684 |
|
| | Connect the prerouted cable. |
| | IMG-462685 |
|
| | Reinstall the removed part. |
| | IMG-462686 |
|
| | Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-464704 |
|
| | Position/route the cable as illustrated. Install the cable. Use a cable tie |
| | IMG-441390 |
|
| | Caution! No grease on contact surfaces. |
Cable from front socket Lubricate the O-ring. |
| | IMG-445566 |
|
| | Cable from front socket Engine heater cable
Connect the cable. Install the catch. |
| | IMG-462710 |
|
| | Place the cable tie as illustrated. |
| | IMG-462714 |
|
| | |
| | IMG-462715 |
|
| | Position/route the cable as illustrated. |
| | IMG-462689 |
|
| | Reinstall the removed part. Reinstall the screws. Reinstall the clips. |
| | IMG-462712 |
|
| | Install the marked components. |
| | IMG-462716 |
|
| | Position/route the cable as illustrated. Install the cable. Use a cable tie |
| | IMG-462717 |
|
| | Install a clips onto the upper edge of the subframe. Position/route the cable as illustrated. Install the cable. |
| | IMG-462719 |
|
| | Position/route the cable as illustrated. Install the cable. Use a cable tie |
| | IMG-465316 |
|
| | Steering gear Cable harness Engine heater cable
|
| | IMG-462742 |
|
| | Caution! The cable ties must not be assembled around the steering gear wiring harness. |
Note! Fasten the cable ties without tightening. |
Position/route the cable as illustrated. Install the cable. |
| | |
| | IMG-468911 |
|
| | Loosen the clip. Fold marked part aside. |
| | |
| | IMG-468829 |
|
| | Remove the clip. Remove the marked part. |
| | IMG-468837 |
|
| | |
| | IMG-465196 |
|
| | Remove the protective film. |
| | IMG-468840 |
|
| | Install components that come with the accessory kit. Tighten the bolts. |
| | |
| | IMG-468915 |
|
| | Install the marked component. |
| | |
| | IMG-468841 |
|
| | Use: Scribe
Use: Pop rivet pliers
|
| | IMG-441390 |
|
| | |
| | IMG-468847 |
|
| | Connect the cable. Install the catch. |
| | IMG-465285 |
|
| | Fasten the cable tie without tightening. Adjust the cable position so that it can follow the motions of the engine. Tighten the cable tie. |
| | IMG-465329 |
|
| | |
| | |
| | Reinstall the removed parts in reverse order. |
| | IMG-405228 |
|
| | Note! Make sure to follow the sequence indicated. |
Tightening torque: Aluminum wheel rim to wheel hub Stage 1:
4 Nm Stage 2:
50 Nm Stage 3:
140 Nm
|